Kenmore 625.348252, 625.348242, 625.348235 owner manual Ipowerokayi

SECTION 5SERVICE mECH. INFORMATION

A. TROUBLESHOOTING

NEUTRAUZER	FILTER			TASTE	& ODOR	RLTER
FILTERED WATER IS ACID		FILTEREDWATER CONTAINS SEDIMENTS,		FILTERED	WATER	bIAS TASTE
(LOW	pH)	(SAND, StLT,,DIRT, ETC.) OR IRON	I	AND/OR ODOR
		ALL FILTERS

!

OTHER WATERCONDITIONING

I IRON(HAVEINWATERREQUIRESANALYZED) I

NEUTRALITE M INERAL

NEEDS REFILL OF i

TIMER DISPLAYSHOWS CORRECT

TIME AND DAY, AND IS STEADY

1

1.Is raw water pipe plumbed to valve inlet?

iIs plumbing bypass valve(s) in service?

Is valve drainhoseV,SUAunobstructed?OHEO S

TIMER SHOWSWRONGTIME I

AND DAY AND/0B S FLASH NG I

OF ACTIVATED CARBON

INEEDS MINERALREPLACEMENT

[TIMERDISPLAYDLANK

i

OBSERVEVALVE CAM POSITION l

I'NERV,PDS,,,ONE I [ OTINSERV,OEPOSITIO

TEST WATERAT FILTEREDWATER /			1.	Wiring	harness		has loose
FAUCETCLOSESTTO FILTER		J		connections,		or	defective
	t		2.	Switch	defective
		_	3.	Valve	motor	inoperative
t NOSED'MENTS1	WATER	CONTAIN 4
IN WATER I	SEDIMENTS 1

=

	i
Electrical power was off.	I
Reset all timer programming	I

Investigatereasonfor powerloss. Besure out-

let for filter cannot be switchedoff.

Diagnosticto verify pro- J Do ManualAdvance I

per function.

÷

Check electrical power to timer (outlet, trans- former, all connections)

t

IPOWEROKAYI

FACE PLATE

DEFECTVE

/

ICHECK PROGRAMMING

Filterregeneratedsince		f
		f			f
customer railed. Checkfor				i
correctregenerationpro-	PROGRAMMINGOK			I	TOO FEW BACK-
gramming.
f	FOR FAMILY NEEDS			I	GRAMMED.
					WASHES PRO-
[ Do Manual Advance Diagnostic I	1.	Leaking faucet or			REPROGRAM_	Do ManualAdvanceDiagnostic to l
to verify proper function.								/
		stool	I		_	ver fy proper function.	I
	2.	Filteredwater usebl		DOMANUALADVANCETO I
		atoutaidefaucetsLI					/
	3.	Otherunusual fil-	r,P-i FILL CYCLE- CHECKFILL
		tered waterusage/I		FLOWTO SOLUTON B0rFLE			/

/

/

/

/

/

FACEPLATE REPLACEMENT: BE SURE THE VALVE IS IN SERVICE POSITION (OBSERVE VALVE

CYCLE INDICATOR) WHEN REPLACING THE FACEPLATE.

If after installing and programming the replacement faceplate, the valve is not inM

service position, do the following to assure correct cycle orientation, or timing,

between the faceplate and valve.

S • (SERVICE)

Use the MANUAL ADVANCE procedures,	page	5- 3. With	the	the	RECHARGE
button, advance through the recharge cycles until		the valve	stops	in	service posi-	Valve
						Position
tion, and RECHARGE no longer flashes in	the timer.				Valve
						Indicator
					Cam

NOTE: The valve motor may automatically drive through several valve positions

while searching for service.

5-4

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line