Kenmore 625.348261 owner manual Cleaning the Filter Resin BED, Nozzle and Venturi

Page 14

I

 

 

 

 

SECTION3

 

 

 

CARE OF YOUR FILTER

 

 

 

 

C. CLEANING THE FILTER RESIN BED

 

 

 

 

To keep

the tannin

resin

bed

clean

and

working

thoroughly

stirred,

pour the

solution

directly

into

efficientlN

do

the

following

at

least

once

each

the

brinewell

(see

key no.

25,

page

6-2).

 

month.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use one

gallon

of luke

warm

 

water

(do

not

use hot

The

solution

will

be drawn

into and

through

the

water) to fully

dissolve

1 cup

of soda ash.

After

resin

bed during

filter regenerations.

 

 

D. CLEANING THE

A clean nozzle and venturi (Figure 12) is a must for the filter to work right. This small unit moves brine from the salt storage tank to the resin tank

during regeneration. If it becomes plugged with sand, silt, dirt, etc., the filter will not work and

you will get unfiltered water.

Be sure the filter is in service cycle (no water pres-

sure at nozzle and venturi), then turn off the cap

from the nozzle and venturi housing. Lift out the

screen support and screen, then the nozzle and

venturi. Wash and rinse the parts in warm water until clean. If needed use a small brush to remove

iron or dirt. Also check and clean the gasket and flow plug if dirty.

Carefully replace all parts in the correct order. Lu- bricate the o-ring seal with silicone grease or Vase- line and place in position. Install and tighten the

cap, BY HAND ONLY. DO NOT OVER TIGHTEN AND BREAK THE CAP OR HOUSING.

It is recommended that you clean the nozzle and venturi at least three times a year. Clean more often if you notice a difference in water quality.

NOZZLE AND VENTURI

Ill [dIJ ;1=1il,d

NOTE: Be sure holes in the

gasket align with the holes at the bottom of the nozzle &

venturi housing.

*INSTALL WITH

NUMBERED SIDE UP, CONCAVE SIDE DOWN

3-2

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Image 14
Contents Owners Manual Save this ManualSears Installation Policy Sears Installation Warranty Sears Residential Water FilterN T E N Safety Guides Water Filter Start UPINLET? Check List of ALL STEP-BY-STEP Guides to InstallSERVICE? Program the Timer SET Present Time of DAYSET Days to Recharge TimerProgram SET Recharge TimeSanitizing the Water Filter RechargenowVacation Faceplate Timer FeaturesHOW Your Water Filter Works Timer POWER- Outage Memory Adjustable Brine DrawAdjustable Fast Rinse Adjustable BackwashService Filtered WATER, Service and RegenerationService Tannin WaterAutomatic Bypass Brining / Brine RinseFast Rinse Breaking Care of Your FilterChecking the Salt Storage Level and Refilling Salt BridgeNozzle and Venturi Cleaning the Filter Resin BEDCleaning Care Your Filter Keep the Filter from FreezingBefore YOU Call for Service Helpful Hints Checklist Problem Cause Correction No Filtered WaterDimensions Specifications Other Things to KnowOther Things to Know Service TECH. Information Wiring SchematicSwitch Valve Cycle Status Displays TroubleshootingManual Initiated Electronics Diagnostic Always Make These Initial Checks FirstPossible Defect Code Manual Advance DiagnosticsAutomatic Electronic Diagnostics Most Likely Least LikelyAssembly Rotary Valve ServiceDisassembly Servicing the ValveService Cycle Water Flow Through the Filter ValveBrining and Brine Rinse Cycles Brine From Salt Storage TankFast Rinse Cycle Rotor & Disc Position Switch Repair Parts KEY Part Description Problems, Questions? Call 1-800-426-9345 Kenmore Water Line KEY Part Repair Parts Repair Parts Your Home