Replacing the Line, Replacing the Cutting Head

REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) di- ameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes					Line in Notch

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

REPLACING THE CUTTING HEAD

1.Push in locking lever and hold.

2.Rotate dust cup until the locking lever falls into one of the grooves.

Locking Lever

3.Continue to hold in locking lever. This will prevent the shaft from turning while re- moving and installing trimmer head.

4.Remove trimmer head by turning clock- wise.

5.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

6.Release locking lever.

CARBURETOR ADJUSTMENT

Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an au- thorized service dealer. Damage will occur if you turn the needles beyond the limiter stops.

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans-

porting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy

storage.

SStore in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

XT600 specifications

The Weed Eater XT600 is a powerful and versatile string trimmer designed for homeowners and landscaping professionals seeking efficiency and reliability in their lawn care equipment. This trimmer combines innovative technology with user-friendly features to tackle a variety of yard maintenance tasks.

One of the standout features of the Weed Eater XT600 is its robust 22cc engine, which provides ample power for cutting through tough weeds and thick grass. This gas-powered engine is designed for optimum performance, ensuring that users can complete their outdoor tasks quickly and effectively. The XT600’s lightweight design further enhances maneuverability, making it easier to navigate around flower beds, fences, and other obstacles.

The XT600 employs a split-shaft design that allows for easy attachment of various accessories. This versatility makes it more than just a string trimmer; users can convert it into a blower, edger, or pruner, providing multiple solutions for yard maintenance with a single machine. Changing attachments is straightforward, allowing for seamless transitions between different tasks.

Equipped with a dual-line auto-feed system, the Weed Eater XT600 ensures that the cutting line advances automatically as needed, eliminating the hassle of stopping and manually adjusting the line. This feature not only saves time but also improves cutting efficiency, as users can maintain consistent trimming without interruptions.

Comfort is another priority for the XT600, which comes with an ergonomic handle design that reduces fatigue during prolonged use. The trimmer's lightweight frame and balanced weight distribution help users maintain control, leading to cleaner cuts and more precise trimming.

In terms of build quality, the XT600 features durable components that can withstand the rigors of regular use. The trimmer is designed to handle variable outdoor conditions, making it a reliable tool for various landscaping projects.

Additionally, the XT600 includes easy-start technology that simplifies the ignition process. This feature ensures that users can start the trimmer with minimal effort, reducing frustration and getting them back to work quickly.

Overall, the Weed Eater XT600 stands out in the market for its combination of power, versatility, and user-friendly features. Whether you are a homeowner looking to maintain a neat lawn or a landscaping professional needing a reliable trimmer, the XT600 provides the performance and adaptability needed to tackle any yard work with confidence.