Murray 96017000700 manual To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

IDLER PULLEYS

MANDREL PULLEYS

FIG. 18

TO CHECK AND ADJUST BRAKE (See Fig. 19)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

Depress clutch/brake pedal all the way down and engage parking brake.

Measure distance between brake operating arm and nut “A” on brake rod.

If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

WITH PARKING BRAKE “ENGAGED”

1-1/2"

NUT “A”

JAM NUT

OPERATING ARM

FIG. 19

21

Engage transmission by placing freewheel control in “transmission engaged” position.

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Remove belt from stationary idler and clutching idler.

Remove belt downward from around engine pulley.

Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down between transaxle belt keepers and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top groove of engine pulley.

Install belt through stationary idler and clutching idler.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSAXLE

PULLEY

FIG. 20

Image 21
Contents Always Wear EYE Protection During Operation ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack To Remove Tractor from Carton Tools Required for AssemblyBefore Removing Tractor from Skid Unpack CartonInstall Mulcher Plate See If previously removed Check Battery See FigCheck Tire Pressure C O N V E R T T O B a G G I N G O R DischargingCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the ROSTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionRunning Maintenance Blade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerTo Remove Mower See Fig To Install Mower See FigBelt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsEngine dies when Suggested Guide for Sighting Slopes for Safe Operation Mississauga, Ontario Customer Service Courtneypark Dr. East6662-661-800-1 Limitée GarantieDegrés Défectueux est Dépannage DE GuideRalenti Moteur EntreposageMoteur Réglages ET RévisionAVANT/ Roues DES Convergence CarrossageDI LA DE L’ALIGNEMENT Régler Pour Vitesses DE Boîte LA DE MentgechanCourroie LA Remplacer Pour Frein LE Régler ET Contrôler PourTransmission DE MENTNETRAÎD’EN DE Boîtier LE Niveau DE Mettre Pour Courroie Acer Rempl PourTondeuse DE Lame DE MENTNETRAÎD’EN SedeutonReglages ET Revision Fig la Voir Tondeuse LA Installer PourTracteur Tondeuse LA Enlever PourEntretien Ligne EN Installé D’ESSENCE Filtre’ALLUMAGE Bougie AIR À FiltreLubrification Transmission LA DE RefroidissementTrapézoïdales Courroies 11 .FIGFig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Générales Recommandations LESLubrification DE Tableau Utilisation Chaque AvantTonte DE Conseils UtilisationTransmission LA Purger 8b .FIGMoteur LE Démarrer DE Avant Tracteur LE Transporter Pour 8a .Fig les VoirPentes LES Dans Utiliser Pour Tondeuse LA Utiliser PourTeurtrac E R T O V R E S I L I T U T N E M M O C GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir Mentnetionsta DE Frein LE Engager Pour02829 ’EMBRAYAGE Montage Décharge LAOU Ramassage AU Convertir Pour Déchiqueteuse Plaque LA Installer Retirée Auparavant SIPA LA DE Tracteur LE Retirer Pour LE Pour Exigés Outils LES DU Tracteur LE Sortir PourPalette LA DE Tracteur LE Retirer DE Avant ToncarClés Montar SIN PiezasSommaire Client DU ResponsabilitésProduit DE Spécifications Remorquage EntretienEnfants Général EntretienPentes LES Dans FonctionnementGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsPelouse DE Tracteur Modèle Propriétaire DU Manuel

96017000700 specifications

Murray 96017000700 is a versatile outdoor power equipment known for its robust design and efficient performance. This model is primarily a push mower, making it an ideal choice for homeowners seeking reliable and powerful lawn maintenance tools. Its features and technologies are tailored to provide an effective mowing experience, making it a popular choice among gardening enthusiasts.

One of the standout features of the Murray 96017000700 is its powerful engine. It is equipped with a reliable gas-powered engine that ensures strong performance across various mowing conditions. This engine provides the necessary torque to tackle thick grass and uneven terrains, allowing users to achieve a clean and manicured lawn effortlessly.

The mower boasts a cutting deck that is designed for durability and efficiency. Constructed from high-quality materials, the deck is both lightweight and strong, which helps in providing longevity to the product. Its cutting width allows for efficient mowing of large areas in less time, reducing the effort needed for lawn maintenance.

Another significant characteristic of the Murray 96017000700 is its adjustable cutting height feature. Users can easily adjust the height of the mower's blades to suit different grass types and lengths, ensuring a consistent cut tailored to personal preferences. This flexibility is particularly advantageous during the growing season when grass may vary significantly in height.

The ergonomic design of the mower enhances user comfort and control. Its handle is designed for ease of use, making it simple to maneuver around garden beds, trees, and other obstacles. Additionally, the mower includes a reliable starting system that minimizes the effort required to get the engine running, allowing for a hassle-free mowing experience.

In terms of maintenance, the Murray 96017000700 is specifically designed for easy servicing. Routine checks can be conducted with minimum hassle, and the mower's components are accessible for any necessary repairs or replacements. This ease of maintenance ensures that the mower remains in top working condition for years.

Overall, the Murray 96017000700 stands out in the market for its combination of power, durability, and efficiency. With its user-friendly features and solid construction, it is a valuable addition to any homeowner’s gardening toolkit, making lawn care a manageable and straightforward task. Whether tackling small yards or larger lawns, this mower remains a reliable partner for maintaining lush and healthy grass.