Murray 96017000500 manual To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

IDLER PULLEYS

MANDREL PULLEYS

FIG. 18

TO CHECK AND ADJUST BRAKE (See Fig. 19)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-1/2"

NUT “A”

JAM NUT

OPERATING ARM

TO REPLACE MOTION DRIVE BELT (See Fig. 20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSAXLE

PULLEY

FIG. 20

FIG. 19

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Always Wear EYE Protection During Operation ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack To Remove Tractor from Carton Tools Required for AssemblyBefore Removing Tractor from Skid Unpack CartonCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceGeneral Recommendations ScheduleBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerTo Remove Mower See Fig To Install Mower See FigBelt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsEngine dies when Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty 6662-661-800-1 Limitée GarantiePliez EST Degrés Suivant LESDéfectueux est Dépannage DE GuideRalenti Moteur EntreposageMoteur Réglages ET RévisionAVANT/ Roues DES Convergence CarrossageDI LA DE L’ALIGNEMENT Régler Pour Vitesses DE Boîte LA DE MentgechanTransmission DE MENTNETRAÎD’EN Frein LE Régler ET Contrôler PourCourroie LA Remplacer Pour 20 .FIG 19 .FIGDE Boîtier LE Niveau DE Mettre Pour Courroie Acer Rempl PourTondeuse DE Lame DE MENTNETRAÎD’EN SedeutonReglages ET Revision Fig la Voir Tondeuse LA Installer PourTracteur Tondeuse LA Enlever PourEntretien Ligne EN Installé D’ESSENCE Filtre’ALLUMAGE Bougie AIR À FiltreLubrification Transmission LA DE RefroidissementTrapézoïdales Courroies 11 .FIGFig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Générales Recommandations LESLubrification DE Tableau Utilisation Chaque AvantTonte DE Conseils UtilisationMoteur LE Démarrer Pour Moteur LE Démarrer DE Avant’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierET Charrettes DES Remorquer Pour Accessoires AutresTracteur LE Transporter Pour Pentes LES Dans Utiliser PourTeurtrac E R T O V R E S I L I T U T N E M M O C GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir Mentnetionsta DE Frein LE Engager Pour92820 Moteur Montage Desmancom des tionfonc la et Fig la Voir Batterie LA VérifierLA DE Tracteur LE Retirer Pour DesmancomLE Pour Exigés Outils LES DU Tracteur LE Sortir PourPalette LA DE Tracteur LE Retirer DE Avant ToncarPente-Guide Montar SIN PiezasClés Siège Direction de VolantSommaire Client DU ResponsabilitésProduit DE Spécifications Remorquage EntretienEnfants Général EntretienLES Dans Fonctionnement PentesGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsImportant Manuel

96017000500 specifications

Murray 96017000500 represents a cutting-edge technological solution in the realm of industrial generators, designed to cater to diverse power requirements across various sectors. This generator is engineered for reliability, efficiency, and versatility, making it an ideal choice for businesses that necessitate uninterrupted power supply.

One of the standout features of the Murray 96017000500 is its robust power output. With a capacity that easily meets the demands of both small and medium-sized enterprises, this generator ensures that operations can continue smoothly, even during electrical outages. The design is focused on delivering a steady 120/240V output, accommodating a range of equipment and tools.

The generator incorporates advanced engineering that prioritizes fuel efficiency. It operates on a gas-fueled engine which not only enhances performance but also reduces emissions compared to traditional diesel generators. This aspect aligns with the growing global emphasis on sustainable and environmentally friendly practices in business operations.

Durability is another hallmark of the Murray 96017000500. Built with high-quality materials and superior craftsmanship, it is designed to withstand harsh operational conditions. This resilience ensures that the generator can function consistently over extended periods, minimizing downtime and maintenance costs for businesses.

Ease of use is an essential characteristic of this generator. It features an intuitive control panel that allows operators to monitor performance and make adjustments with minimal effort. Quick-connect ports facilitate straightforward setup and integration into existing power systems, making it accessible even for those with limited technical expertise.

Safety features are integrated throughout the design, with overload protection and automatic shut-off mechanisms in place to prevent damage during power surges. These safety measures underscore Murray's commitment to providing products that are not only high-performing but also secure for users.

In terms of portability, the Murray 96017000500 is designed with mobility in mind. Its compact dimensions and lightweight construction allow for easy transportation and installation at various job sites, making it a practical choice for contractors and tradespeople on the move.

In summary, the Murray 96017000500 is a powerful, efficient, and durable generator that meets the demanding needs of contemporary businesses. With its advanced fuel system, user-friendly interface, and built-in safety features, it represents an ideal investment for those looking to ensure a reliable power supply in any situation.
Top Page Image Contents