Murray 96017000500 manual Engine dies when

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine dies when

1.

Reverse operation system

1.

Turn ignition key to

tractor is shifted

 

(ROS) is not "ON" while

 

ROS "ON" position.

into reverse

 

mower or other attachment

 

See Operation section.

 

 

is engaged.

 

 

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves seat

 

 

 

corrected, contact an authorized service center/

with attachment clutch

 

 

 

department.

engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Light switch is “OFF”.

1.

Turn light switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Engine “backfires” when

1.

Engine throttle control not set between half and

1.

Move throttle control between half and full speed

turning engine “OFF”

 

full speed (fast) position before stopping engine.

 

(fast) position before stopping engine.

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model Always Wear EYE Protection During OperationII. Slope Operation Safe Operation Practices for Ride-On MowersGeneral Operation IV. Towing ServiceIII. Children Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart ScheduleTo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemBelts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeLimited Warranty Limitée Garantie 6662-661-800-1Degrés Suivant LES Pliez ESTDépannage DE Guide Défectueux estRalenti Entreposage MoteurRéglages ET Révision MoteurDI LA DE L’ALIGNEMENT Régler Pour CarrossageAVANT/ Roues DES Convergence Vitesses DE Boîte LA DE MentgechanCourroie LA Remplacer Pour Frein LE Régler ET Contrôler PourTransmission DE MENTNETRAÎD’EN 20 .FIG 19 .FIGTondeuse DE Lame DE MENTNETRAÎD’EN Courroie Acer Rempl PourDE Boîtier LE Niveau DE Mettre Pour SedeutonTracteur Fig la Voir Tondeuse LA Installer PourReglages ET Revision Tondeuse LA Enlever Pour’ALLUMAGE Bougie Ligne EN Installé D’ESSENCE FiltreEntretien AIR À FiltreTrapézoïdales Courroies Transmission LA DE RefroidissementLubrification 11 .FIGEN Fonctionnement DE Système ET Fig la Voir Lame LA AffilerFig la Voir Lame LA Enlever Lubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantUtilisation Tonte DE Conseils’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Accessoires AutresET Charrettes DES Remorquer Pour Pentes LES Dans Utiliser PourFig la Voir Arrêter Pour GAZ DES Commande LA Utiliser PourTeurtrac E R T O V R E S I L I T U T N E M M O C Fig la Voir Mentnetionsta DE Frein LE Engager Pour92820 Moteur Montage LA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA VérifierDesmancom des tionfonc la et DesmancomPalette LA DE Tracteur LE Retirer DE Avant DU Tracteur LE Sortir PourLE Pour Exigés Outils LES ToncarClés Montar SIN PiezasPente-Guide Siège Direction de VolantProduit DE Spécifications SommaireClient DU Responsabilités Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsImportant Manuel

96017000500 specifications

Murray 96017000500 represents a cutting-edge technological solution in the realm of industrial generators, designed to cater to diverse power requirements across various sectors. This generator is engineered for reliability, efficiency, and versatility, making it an ideal choice for businesses that necessitate uninterrupted power supply.

One of the standout features of the Murray 96017000500 is its robust power output. With a capacity that easily meets the demands of both small and medium-sized enterprises, this generator ensures that operations can continue smoothly, even during electrical outages. The design is focused on delivering a steady 120/240V output, accommodating a range of equipment and tools.

The generator incorporates advanced engineering that prioritizes fuel efficiency. It operates on a gas-fueled engine which not only enhances performance but also reduces emissions compared to traditional diesel generators. This aspect aligns with the growing global emphasis on sustainable and environmentally friendly practices in business operations.

Durability is another hallmark of the Murray 96017000500. Built with high-quality materials and superior craftsmanship, it is designed to withstand harsh operational conditions. This resilience ensures that the generator can function consistently over extended periods, minimizing downtime and maintenance costs for businesses.

Ease of use is an essential characteristic of this generator. It features an intuitive control panel that allows operators to monitor performance and make adjustments with minimal effort. Quick-connect ports facilitate straightforward setup and integration into existing power systems, making it accessible even for those with limited technical expertise.

Safety features are integrated throughout the design, with overload protection and automatic shut-off mechanisms in place to prevent damage during power surges. These safety measures underscore Murray's commitment to providing products that are not only high-performing but also secure for users.

In terms of portability, the Murray 96017000500 is designed with mobility in mind. Its compact dimensions and lightweight construction allow for easy transportation and installation at various job sites, making it a practical choice for contractors and tradespeople on the move.

In summary, the Murray 96017000500 is a powerful, efficient, and durable generator that meets the demanding needs of contemporary businesses. With its advanced fuel system, user-friendly interface, and built-in safety features, it represents an ideal investment for those looking to ensure a reliable power supply in any situation.
Top Page Image Contents