Tools Required for Assembly, Unpack Carton

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench Utility knife

(1)3/4" wrench Tire pressure gauge Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK

WASHER

LARGE FLAT WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

			19	TAB
0	2	8	19	SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

96017000500 specifications

Murray 96017000500 represents a cutting-edge technological solution in the realm of industrial generators, designed to cater to diverse power requirements across various sectors. This generator is engineered for reliability, efficiency, and versatility, making it an ideal choice for businesses that necessitate uninterrupted power supply.

One of the standout features of the Murray 96017000500 is its robust power output. With a capacity that easily meets the demands of both small and medium-sized enterprises, this generator ensures that operations can continue smoothly, even during electrical outages. The design is focused on delivering a steady 120/240V output, accommodating a range of equipment and tools.

The generator incorporates advanced engineering that prioritizes fuel efficiency. It operates on a gas-fueled engine which not only enhances performance but also reduces emissions compared to traditional diesel generators. This aspect aligns with the growing global emphasis on sustainable and environmentally friendly practices in business operations.

Durability is another hallmark of the Murray 96017000500. Built with high-quality materials and superior craftsmanship, it is designed to withstand harsh operational conditions. This resilience ensures that the generator can function consistently over extended periods, minimizing downtime and maintenance costs for businesses.

Ease of use is an essential characteristic of this generator. It features an intuitive control panel that allows operators to monitor performance and make adjustments with minimal effort. Quick-connect ports facilitate straightforward setup and integration into existing power systems, making it accessible even for those with limited technical expertise.

Safety features are integrated throughout the design, with overload protection and automatic shut-off mechanisms in place to prevent damage during power surges. These safety measures underscore Murray's commitment to providing products that are not only high-performing but also secure for users.

In terms of portability, the Murray 96017000500 is designed with mobility in mind. Its compact dimensions and lightweight construction allow for easy transportation and installation at various job sites, making it a practical choice for contractors and tradespeople on the move.

In summary, the Murray 96017000500 is a powerful, efficient, and durable generator that meets the demanding needs of contemporary businesses. With its advanced fuel system, user-friendly interface, and built-in safety features, it represents an ideal investment for those looking to ensure a reliable power supply in any situation.