Murray MB12538LT To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 14

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “D”is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 17

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 18)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work new belt around both mandrel pulleys and idler pulleys.

•Install new belt into engine pulley groove.

•Make sure belt is inside the belt keeper at the idler and on both sides of the wire belt keeper as shown.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents MB12538LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

MB12538LT specifications

The Murray MB12538LT is a versatile and robust lawn mower designed for both residential and light commercial use. This model combines innovative technology with user-friendly features, making it an excellent choice for homeowners and landscaping professionals alike. One of the standout features of the MB12538LT is its powerful 125cc engine, which provides ample power to tackle tough mowing conditions. The engine is designed for efficiency, ensuring that users can cover more ground with less fuel consumption.

Another significant characteristic of the Murray MB12538LT is its cutting deck. With a 38-inch cutting width, it allows for efficient mowing of medium to large lawns. The deck is constructed from durable materials, ensuring longevity and resistance to wear and tear. Additionally, the mower offers multiple cutting heights, ranging from 1 inch to 3.5 inches, allowing users to customize their mowing experience based on the grass type and condition.

Murray has integrated advanced technologies into the MB12538LT to enhance user experience. The push-button start feature simplifies the starting process, eliminating the need for cumbersome pull cords. The mower also includes an ergonomic handle that can be adjusted for comfort, aiding users in maintaining a healthy posture while mowing.

One of the most appealing aspects of the MB12538LT is its lightweight design, which makes it easy to maneuver in tight spaces and around obstacles such as trees and flower beds. The rear-wheel drive system enhances traction, providing stability and control on slopes and uneven terrain.

Maintenance is straightforward with the Murray MB12538LT, as it is equipped with readily accessible components for easy oil changes and blade replacement. The mower's design includes a grass bagging option, allowing for efficient grass collection and disposal, which promotes a cleaner lawn and reduces the need for raking.

In summary, the Murray MB12538LT is an excellent choice for those seeking a reliable, easy-to-use lawn mower with essential features that promote efficiency and comfort. With its powerful engine, durable construction, and thoughtful design, it stands out in the crowded market of lawn care equipment. Whether you're a homeowner looking to maintain a tidy lawn or a professional landscaper in need of an efficient tool, the MB12538LT meets various mowing needs with reliability and performance.
Top Page Image Contents