Murray How to Replace the Motion Drive Belt for Lawn Mowers
Page 29

MAINTENANCE

HOW TO REPLACE

THE MOTION DRIVE BELT

REMOVAL

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Completely push the pedal forward and engage the parking brake.

3.Remove the idler pulley (Figure 30).

Drive Pulley

Motion

Drive Belt

Idler Pulley

Loosen The

Belt Guides

Figure 30

4.To access the belt guides, remove the battery and battery tray. See “How To Remove The Battery”.

5.Loosen the belt guides at the drive pulley (Figure 31).

Seat Spring

Belt Guides

Figure 31

6.Remove the motion drive belt from the drive pulley (Figure 30).

7.Remove the adjuster nut from the shifter bracket (Figure 32). Pull the motion drive belt over the shifter bracket.

Shift

 

Link

Adjuster Nut

 

 

Shifter

 

Bracket

 

Hair

 

Pin

Motion Drive Belt

 

 

Figure 32

8.To remove the motion drive belt from the stack pulley, pull the front end of the belt under the stack pulley and then back between the stack pulley and the steering plate (Figure 33).

FRONT

Stack Pulley

Steering

 

 

Plate

Motion

Belt Guides

 

Drive

 

Belt

Figure 33

9.Remove the access panel (Figure 34).

10.Remove the two screws that attach the steering shaft assembly (Figure 34). Raise the steering wheel and steering shaft assembly. Pull the motion drive belt under the steering shaft assembly.

Screw

 

 

Steering Shaft

 

 

Assembly

 

 

Motion Drive

 

 

Belt

Access Panel

Figure 34

 

11.Remove the motion drive belt. A correct replacement part or assistance is available from an Authorized Service Center in your area.

F–030723L

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Gauge Wheels HOW to Install the SeatHOW to Assemble the Steering Wheel HOW to Install the Battery Cables Maintenance Free BatteryHOW to Charge Maintenance Free Battery IMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineLift Lever OperationLocation of Controls HOW to USE the Shift Lever HOW to USE THROTTLE/CHOKE ControlAttachments See the Instruction Book for the AttachmentHOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineBefore Starting the Engine Mowing and Bagging Tips Operating TipsFrequency Maintenance Required Comments MaintenanceHOW to Check the Muffler General RecommendationsInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchDisconnect the adjuster nut from the shifter bracket Figure HOW to Adjust the Shift LeverHOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing Removal HOW to Replace Motion Drive BeltInstallation HOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryTrouble Shooting Chart 030723L MURRAY, INC. Lawn Mower Central Parts DistributorsRepair Parts Chassis & Hood Key Description Repair PartsChassis & Hood Motion Drive Motion Drive Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Repair Parts Repair Parts Engine Mount Engine Mount Repair Parts Electrical System Electrical System 030723L Index Model No Bushel Capacity Model No

425007x92C specifications

Murray 425007x92C is a versatile and efficient piece of machinery that has garnered attention for its remarkable features and cutting-edge technologies. This model integrates advanced engineering with practical applications, making it a valuable asset in various industries.

One of the main features of the Murray 425007x92C is its powerful engine. Designed for optimal performance, this machinery is equipped with a high-capacity powertrain that delivers consistent output even in the most demanding conditions. This not only enhances its operational efficiency but also contributes to reduced overall fuel consumption, which translates to cost savings for users.

The innovative design of the Murray 425007x92C includes a user-friendly interface that simplifies operation and improves workflow. Operators can easily navigate through controls, with strategically placed buttons and levers that ensure intuitive handling. This focus on usability minimizes the learning curve for new operators, increasing productivity right from the start.

In terms of technology, the Murray 425007x92C incorporates state-of-the-art safety features. These include advanced braking systems and stability controls that provide enhanced safety for operators and bystanders alike. Furthermore, the machinery is equipped with real-time diagnostic tools that monitor its performance and alert users to any potential issues before they escalate. This emphasis on safety and reliability ensures that downtime is minimized.

The construction of the Murray 425007x92C emphasizes durability. Made from high-quality materials, it resists wear and tear and is built to withstand harsh working environments. This robust construction not only enhances its lifespan but also decreases the need for frequent maintenance, making it a cost-effective choice for businesses.

Another distinguishing characteristic of the Murray 425007x92C is its adaptability. It can be easily customized with various attachments that cater to different tasks, ranging from landscaping to heavy construction. This versatility allows operators to switch between applications seamlessly, maximizing productivity and making it an indispensable tool for contractors and maintenance personnel.

Overall, the Murray 425007x92C stands out for its combination of power, safety, durability, and adaptability. Whether used in construction, agricultural, or industrial settings, it proves to be a reliable and efficient solution for various operational needs, reflecting modern engineering excellence.
Top Page Image Contents