Murray 425007x92C Attachments, HOW to USE THROTTLE/CHOKE Control, HOW to USE the Shift Lever

Page 15

OPERATION

ATTACHMENTS

This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper, a lawn aerator, a hopper spreader, or a small trailer. This unit can not use attachments that engage the ground like a plow, a disk harrow, or a cultivator.

For all pull–behind attachments or trailers, the maximum gross weight is 250 pounds. Gross weight is the weight of the attachment or trailer and any load that might be on or in it.

Do not operate on a slope that is greater than 10 degrees when using a pull–behind attachment or trailer. We have included a slope guide in this book to help you determine the slope on which you will be operating your unit. Never allow someone to stand or ride on or in an attachment or trailer.

HOW TO USE

THE THROTTLE/CHOKE CONTROL

Use the throttle/choke control to choke the engine for cold starts and increase or decrease the speed of the engine.

1.Move the throttle/choke control completely forward to the CHOKE position to start a cold engine.

2.The FAST position is marked with a detent. For normal opera- tion and when using a grass bagger, move the throttle control to the FAST position. For maximum charging of the battery and for a cooler running engine, operate the engine in the FAST position.

3.The engine governor is set at the factory for maximum perfor- mance. Do not adjust the governor to increase the speed of the engine.

HOW TO USE THE BLADE ROTATION CONTROL

Use the blade rotation control to engage the blade(s) (Figure 6).

Disengage

Position

Blade Rotation Control

Engage Position

Figure 6

1.Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position.

2.Move the blade rotation control to the ENGAGE position to rotate the blade(s).

NOTE: If the engine stops when you engage the blade(s), the seat switch is not activated. Make sure you sit in the middle of the seat.

3.Move the blade rotation control to the DISENGAGE position to stop the blade(s). Before you leave the operator’s position, make sure the blade(s) has stopped rotating.

4.Before you ride the unit across a sidewalk or a road, move the blade rotation control to the DISENGAGE position.

WARNING: Always keep your hands and feet away from the blade, deflector opening, and the mower housing when the engine runs.

HOW TO USE THE SHIFT LEVER

To change the forward speed or the direction of the unit, follow the steps below.

CAUTION: Before you move the shift lever, completely push the clutch/brake pedal forward to stop the unit. If the unit is not stopped, the gearbox can be damaged.

1.Completely push the clutch/brake pedal forward to stop the unit. Keep your foot on the pedal.

2.Move the throttle control lever to the SLOW position.

3.To go forward, move the shift lever to a forward speed setting. To go backward, move the shift lever to reverse.

4.Slowly release the clutch/brake pedal. Do not keep your foot on the pedal.

5.Move the throttle control to the FAST position.

FUNCTION

SHIFT LEVER

THROTTLE

 

6 Speeds

 

 

 

 

Trimming

1

 

Snow Thrower

 

 

 

 

 

Bagging Grass

1 or 2

 

 

 

FAST

Mulching Grass

1 or 2

CHOKE

 

 

 

Normal Mowing

2 or 3

FAST

 

 

 

Easy Mowing

3 or 4

 

Snow Blade

 

SLOW

 

 

THROTTLE

Transport

5 or 6

 

 

 

 

Attachments

*

 

 

 

 

* See the Instruction Book for the Attachment.

F–030723L

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Assemble the Gauge Wheels Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables IMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineOperation Location of ControlsLift Lever See the Instruction Book for the Attachment HOW to USE THROTTLE/CHOKE ControlHOW to USE the Shift Lever AttachmentsHOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchDisconnect the adjuster nut from the shifter bracket Figure HOW to Adjust the Shift LeverHOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing Removal HOW to Replace Motion Drive BeltInstallation HOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart 030723L MURRAY, INC. Lawn Mower Central Parts DistributorsRepair Parts Chassis & Hood Repair Parts Chassis & HoodKey Description Motion Drive Motion Drive Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Repair Parts Repair Parts Engine Mount Engine Mount Repair Parts Electrical System Electrical System 030723L Index Model No Bushel Capacity Model No

425007x92C specifications

Murray 425007x92C is a versatile and efficient piece of machinery that has garnered attention for its remarkable features and cutting-edge technologies. This model integrates advanced engineering with practical applications, making it a valuable asset in various industries.

One of the main features of the Murray 425007x92C is its powerful engine. Designed for optimal performance, this machinery is equipped with a high-capacity powertrain that delivers consistent output even in the most demanding conditions. This not only enhances its operational efficiency but also contributes to reduced overall fuel consumption, which translates to cost savings for users.

The innovative design of the Murray 425007x92C includes a user-friendly interface that simplifies operation and improves workflow. Operators can easily navigate through controls, with strategically placed buttons and levers that ensure intuitive handling. This focus on usability minimizes the learning curve for new operators, increasing productivity right from the start.

In terms of technology, the Murray 425007x92C incorporates state-of-the-art safety features. These include advanced braking systems and stability controls that provide enhanced safety for operators and bystanders alike. Furthermore, the machinery is equipped with real-time diagnostic tools that monitor its performance and alert users to any potential issues before they escalate. This emphasis on safety and reliability ensures that downtime is minimized.

The construction of the Murray 425007x92C emphasizes durability. Made from high-quality materials, it resists wear and tear and is built to withstand harsh working environments. This robust construction not only enhances its lifespan but also decreases the need for frequent maintenance, making it a cost-effective choice for businesses.

Another distinguishing characteristic of the Murray 425007x92C is its adaptability. It can be easily customized with various attachments that cater to different tasks, ranging from landscaping to heavy construction. This versatility allows operators to switch between applications seamlessly, maximizing productivity and making it an indispensable tool for contractors and maintenance personnel.

Overall, the Murray 425007x92C stands out for its combination of power, safety, durability, and adaptability. Whether used in construction, agricultural, or industrial settings, it proves to be a reliable and efficient solution for various operational needs, reflecting modern engineering excellence.
Top Page Image Contents