Sawdust, Wear proper eye protection to keep | Craftsman 137.21194

SAWDUST	Fig. JJ
Periodically, sawdust will accumulate
under the work table and base. This
could cause difﬁculty in the movement
of the worktable when setting up
a miter cut. Frequently blow out or
vacuum up the sawdust.
! WARNING		Central pivot of
Wear proper eye protection to keep	Chop pivot	plastic guard
Wear proper eye protection to keep	Chop pivot
debris from entering eyes when
removing sawdust from unit.
LUBRICATION (FIG. JJ, KK)	Fig. KK
LUBRICATION (FIG. JJ, KK)
All the motor bearings in this tool are		1
lubricated with a sufﬁcient amount of
high grade lubricant for the life of the
unit under normal operating conditions;
therefore, no further lubrication is
required.

Lubricate the Following as necessary:

1

Chop pivot: Apply light machine oil to points indicated in illustration.

Central pivot of plastic guard: Use light household oil (sewing machine oil ) on metal-to-metal or metal-to- plastic guard contact areas as required for smooth, quiet operation. Avoid excessive oil, to which sawdust will cling.

Link: (actuates lower guard movement) If down chop motion is hard to start, oil link at two screws (1).

38

Image 38

Craftsman 137.21194 Sawdust, Wear proper eye protection to keep, Debris from entering eyes when Removing sawdust from unit

Contents

Operator’s Manual Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA Table of Contents Warranty Blade Size Product SpecificationsMotor Rotating Table Support and Clamp Work SymbolsProhibition Always Wear EYE Power Tool SafetyGeneral Safety Instructions Before Using this Power Tool DANGER Compound Miter SAW Safety Specific Safety Instructions for this Compound Miter SAWPage Double Insulated Power Supply and Motor SpecificationsMotor Safety Protection Important Guidelines for Extension Cords Minimum Gauge for Extension Cords AWG Accessories Accessories and AttachmentsRecommended Accessories Combination Square Must be True Tools Needed for AssemblySupplied Not supplied Carton Contents Know Your Sliding Compound Miter SAW Glossary of Terms Woodworking Terms Revolutions PER Minute RPM Installing the Miter Handle FIG. B Assembly and AdjustmentsInstalling the Support Bracket FIG. a Installing the Dust BAG FIG. C Unlocking the Slide Carriage FIG. F SAW Blade Wrench FIG. EReleasing Cutting Head FIG. G Removing and Installing the Table Insert FIG. H Mounting the Miter SAW FIG. I, J Removing or Installing Blade Installing Blade FIG. K, L, M Un-plug the miter saw before changing/installing the blade Avoid Direct EYE Contact Laser Guide FIG. NLaser Beam Bevel Stop Adjustments FIG. O, P, Q Fig. O Bevel Pointer Adjustment Fig. P Adjusting Fence Squareness FIG. S Miter Angle Adjustment FIG. RMiter Scale Indicator Adjustment FIG. R Adjusting Cutting Depth FIG. T Fig. S Troubleshooting Guide for adjustment if necessary Assembly and AdjustmentsRequirements and Safety Before Each USE Inspect Your SAW Operation Inspect Your Workpiece Dress for SafetyPlan Your Work Never cut freehand When SAW is RunningDo not OVER-REACH USE Extra Caution with Large or ODD Shaped Workpieces Before freeing jammed material Body and Hand Position FIG. UFinishing a cut Basic SAW Operations Before Leaving the SAW Sliding Carriage System FIG. WMiter CUT FIG Bevel CUT FIG. Y Compound CUT FIG. Z Rough Cutting a Dado FIG. CC To Slide Cut Wide Boards Fig. AACutting Bowed Material FIG. BB Fig. CC Cutting Crown Molding FIG. GG, HH Bevel/Miter SettingsOnly When the Angle Between the Walls Equals Inside corner-Right side KEY Bevel Miter Type of CUT SettingInside corner-Left side Outside corner-Left side Crown Molding Chart Replacing Carbon Brushes FIG MaintenanceMaintenance Lower Blade Guard Wear proper eye protection to keep Debris from entering eyes when Removing sawdust from unitSawdust Lubrication FIG. JJ, KK Troubleshooting Guide EYE Protection Parts List Parts List for SAW Schematic Schematic 4 in. Compound Miter SAW Model no Parts List for Motor Description Size Qty SU-HOGAR R Sears Parts & Repair Service CenterLE-FOYER MC