To Slide Cut Wide Boards Fig. AA | Craftsman 137.21194 specification

To Slide Cut Wide Boards (Fig. AA)

1.Unlock the carriage lock handle

(1) and allow the cutting head assembly to move freely.

2.Set both the desired bevel angle and/or the miter angle and lock into position.

3.Use a hold down clamp to secure the workpiece.

4.Grasp and pull forward the switch handle (2) until the center of the saw blade is over the front of the workpiece (3).

5.Engage the trigger to turn the saw on.

6.When the saw reaches full speed, push the switch handle down, slowly, cutting through the leading edge of the workpiece.

7.Slowly move the switch handle toward the fence, completing the cut.

8.Release the trigger and allow the blade to stop spinning before allowing the cutting head to raise.

Fig. AA

1

2

3

CUTTING BOWED MATERIAL (FIG. BB)

!WARNING

To avoid injury from materials being thrown, always unplug the saw

to avoid accidental starting and remove small pieces of material from the table cavity.

The table insert may be removed for this purpose, but always reattach table insert prior to performing a cutting operation.

A bowed workpiece must be positioned against the fence and secured with

a clamping device as shown before cutting. Do not position workpiece incorrectly or try to cut the workpiece without the support of the fence. This will cause the blade to bind and could result in personal injury.

Fig. BB

ROUGH CUTTING A DADO (FIG. CC)

!WARNING

DO NOT USE A DADO BLADE, use only the standard saw blade for this operation.

1.Mark lines identifying the width and depth of the desired cut on

32

Image 32

Craftsman 137.21194 To Slide Cut Wide Boards Fig. AA, Cutting Bowed Material FIG. BB, Rough Cutting a Dado FIG. CC

Contents

Operator’s Manual Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA Table of Contents Warranty Product Specifications MotorBlade Size Rotating Table Support and Clamp Work SymbolsProhibition Always Wear EYE Power Tool SafetyGeneral Safety Instructions Before Using this Power Tool DANGER Compound Miter SAW Safety Specific Safety Instructions for this Compound Miter SAWPage Double Insulated Power Supply and Motor SpecificationsMotor Safety Protection Important Guidelines for Extension Cords Minimum Gauge for Extension Cords AWG Accessories Accessories and AttachmentsRecommended Accessories Combination Square Must be True Tools Needed for AssemblySupplied Not supplied Carton Contents Know Your Sliding Compound Miter SAW Glossary of Terms Woodworking Terms Revolutions PER Minute RPM Assembly and Adjustments Installing the Support Bracket FIG. aInstalling the Miter Handle FIG. B Installing the Dust BAG FIG. C Unlocking the Slide Carriage FIG. F SAW Blade Wrench FIG. EReleasing Cutting Head FIG. G Removing and Installing the Table Insert FIG. H Mounting the Miter SAW FIG. I, J Removing or Installing Blade Installing Blade FIG. K, L, M Un-plug the miter saw before changing/installing the blade Avoid Direct EYE Contact Laser Guide FIG. NLaser Beam Bevel Stop Adjustments FIG. O, P, Q Fig. O Bevel Pointer Adjustment Fig. P Adjusting Fence Squareness FIG. S Miter Angle Adjustment FIG. RMiter Scale Indicator Adjustment FIG. R Adjusting Cutting Depth FIG. T Fig. S Assembly and Adjustments Requirements and Safety Before Each USE Inspect Your SAWTroubleshooting Guide for adjustment if necessary Operation Inspect Your Workpiece Dress for SafetyPlan Your Work When SAW is Running Do not OVER-REACHNever cut freehand USE Extra Caution with Large or ODD Shaped Workpieces Body and Hand Position FIG. U Finishing a cutBefore freeing jammed material Basic SAW Operations Before Leaving the SAW Sliding Carriage System FIG. WMiter CUT FIG Bevel CUT FIG. Y Compound CUT FIG. Z Rough Cutting a Dado FIG. CC To Slide Cut Wide Boards Fig. AACutting Bowed Material FIG. BB Fig. CC Cutting Crown Molding FIG. GG, HH Bevel/Miter SettingsOnly When the Angle Between the Walls Equals KEY Bevel Miter Type of CUT Setting Inside corner-Left sideInside corner-Right side Outside corner-Left side Crown Molding Chart Maintenance MaintenanceReplacing Carbon Brushes FIG Lower Blade Guard Debris from entering eyes when Removing sawdust from unit SawdustWear proper eye protection to keep Lubrication FIG. JJ, KK Troubleshooting Guide EYE Protection Parts List Parts List for SAW Schematic Schematic 4 in. Compound Miter SAW Model no Parts List for Motor Description Size Qty SU-HOGAR R Sears Parts & Repair Service CenterLE-FOYER MC