SAW Blade Wrench FIG. E | Craftsman 137.21194 specs

Fig. D

2

3 1

SAW BLADE WRENCH (FIG. E)

For convenient storage and prevention of loss, there is a slot (1) in the right side of the switch handle (2) for storing the blade wrench (3) when not in use.

Fig. E

RELEASING CUTTING HEAD (FIG. G)

!WARNING

To avoid injury and damage to the saw, transport or store the miter saw with the cutting head locked in the down position. Never use the hold down latch to hold the cutting head in a down position for cutting operations.

Unlocking

1.Push down slightly on the switch handle (1).

2.Pull out the hold-down latch (2).

3.Allow the cutting head to rise to the up position.

Fig. G

2

1

2

1

3

UNLOCKING THE SLIDE CARRIAGE (FIG. F)

After removing the saw from the carton, loosen the slide carriage lock knob

(1). When transporting or storing the miter saw, the slide carriage should always be locked in position. The slide carriage lock knob (1) is located on the right side of the slide carriage.

Fig. F

1

Locking

When transporting or storing the miter saw, the cutting head should always be locked in the down position.

1.Push the cutting head down to its lowest position.

2.Push the hold-down latch (2) into the locking hole.

IMPORTANT: To avoid damage, never carry the miter saw by the switch handle, the cutting arm or the miter handle. Only lift machine by the base hand holds.

!WARNING

To avoid injury, disconnect the plug from the power source before performing any adjustments or repair.

18

Image 18

Craftsman 137.21194 SAW Blade Wrench FIG. E, Releasing Cutting Head FIG. G, Unlocking the Slide Carriage FIG. F

Contents

Operator’s Manual Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA Table of Contents Warranty Blade Size Product SpecificationsMotor Rotating Table Symbols ProhibitionSupport and Clamp Work Power Tool Safety General Safety Instructions Before Using this Power ToolAlways Wear EYE DANGER Compound Miter SAW Safety Specific Safety Instructions for this Compound Miter SAWPage Power Supply and Motor Specifications Motor Safety Protection ImportantDouble Insulated Guidelines for Extension Cords Minimum Gauge for Extension Cords AWG Accessories and Attachments Recommended AccessoriesAccessories Tools Needed for Assembly Supplied Not suppliedCombination Square Must be True Carton Contents Know Your Sliding Compound Miter SAW Glossary of Terms Woodworking Terms Revolutions PER Minute RPM Installing the Miter Handle FIG. B Assembly and AdjustmentsInstalling the Support Bracket FIG. a Installing the Dust BAG FIG. C SAW Blade Wrench FIG. E Releasing Cutting Head FIG. GUnlocking the Slide Carriage FIG. F Removing and Installing the Table Insert FIG. H Mounting the Miter SAW FIG. I, J Removing or Installing Blade Installing Blade FIG. K, L, M Un-plug the miter saw before changing/installing the blade Laser Guide FIG. N Laser BeamAvoid Direct EYE Contact Bevel Stop Adjustments FIG. O, P, Q Fig. O Bevel Pointer Adjustment Fig. P Miter Angle Adjustment FIG. R Miter Scale Indicator Adjustment FIG. RAdjusting Fence Squareness FIG. S Adjusting Cutting Depth FIG. T Fig. S Troubleshooting Guide for adjustment if necessary Assembly and AdjustmentsRequirements and Safety Before Each USE Inspect Your SAW Operation Dress for Safety Plan Your WorkInspect Your Workpiece Never cut freehand When SAW is RunningDo not OVER-REACH USE Extra Caution with Large or ODD Shaped Workpieces Before freeing jammed material Body and Hand Position FIG. UFinishing a cut Basic SAW Operations Sliding Carriage System FIG. W Miter CUT FIGBefore Leaving the SAW Bevel CUT FIG. Y Compound CUT FIG. Z To Slide Cut Wide Boards Fig. AA Cutting Bowed Material FIG. BBRough Cutting a Dado FIG. CC Fig. CC Bevel/Miter Settings Only When the Angle Between the Walls EqualsCutting Crown Molding FIG. GG, HH Inside corner-Right side KEY Bevel Miter Type of CUT SettingInside corner-Left side Outside corner-Left side Crown Molding Chart Replacing Carbon Brushes FIG MaintenanceMaintenance Lower Blade Guard Wear proper eye protection to keep Debris from entering eyes when Removing sawdust from unitSawdust Lubrication FIG. JJ, KK Troubleshooting Guide EYE Protection Parts List Parts List for SAW Schematic Schematic 4 in. Compound Miter SAW Model no Parts List for Motor Description Size Qty Sears Parts & Repair Service Center LE-FOYER MCSU-HOGAR R