Product Specifications, Motor, Blade Size | Craftsman 137.21194

PRODUCT SPECIFICATIONS

MOTOR
Power Source	9Amp, 120V AC, 60Hz
Speed	5000 RPM (No load)
Brake	Electric
Double Insulated	Yes
BLADE SIZE
Diameter	7-1/4 in.
Arbor size	5/8 in.
ROTATING TABLE:
Diameter	9-1/32 in.
Miter Detent Stops	0, 15, 22.5, 31.6, 45º R & L
Bevel Positive Stops	0, 45º L
CUTTING CAPACITY:
Crosscut	2 in. x 8 in.
Miter 45° R & L	2 in. x 6 in.
Bevel 45º L	1-1/2 in. x 8 in.
45° Miter and 45° Bevel	1-1/2 in. x 6 in.

!WARNING

To avoid electrical hazards, ﬁre hazards or damage to the tool, use proper circuit protection.

This tool is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker. To avoid shock or ﬁre, replace power cord immediately if it is worn, cut or damaged in any way.

Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the tool.

3

Image 3

Craftsman 137.21194 operating instructions Product Specifications, Motor, Blade Size, Rotating Table, Cutting Capacity

Contents

Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA Operator’s Manual Warranty Table of Contents Rotating Table Product SpecificationsMotor Blade Size Symbols ProhibitionSupport and Clamp Work Power Tool Safety General Safety Instructions Before Using this Power ToolAlways Wear EYE DANGER Specific Safety Instructions for this Compound Miter SAW Compound Miter SAW SafetyPage Power Supply and Motor Specifications Motor Safety Protection ImportantDouble Insulated Minimum Gauge for Extension Cords AWG Guidelines for Extension Cords Accessories and Attachments Recommended AccessoriesAccessories Tools Needed for Assembly Supplied Not suppliedCombination Square Must be True Carton Contents Know Your Sliding Compound Miter SAW Glossary of Terms Revolutions PER Minute RPM Woodworking Terms Installing the Dust BAG FIG. C Assembly and AdjustmentsInstalling the Support Bracket FIG. a Installing the Miter Handle FIG. B SAW Blade Wrench FIG. E Releasing Cutting Head FIG. GUnlocking the Slide Carriage FIG. F Mounting the Miter SAW FIG. I, J Removing and Installing the Table Insert FIG. H Blade Removing or Installing Un-plug the miter saw before changing/installing the blade Installing Blade FIG. K, L, M Laser Guide FIG. N Laser BeamAvoid Direct EYE Contact Fig. O Bevel Pointer Adjustment Fig. P Bevel Stop Adjustments FIG. O, P, Q Miter Angle Adjustment FIG. R Miter Scale Indicator Adjustment FIG. RAdjusting Fence Squareness FIG. S Fig. S Adjusting Cutting Depth FIG. T Operation Assembly and AdjustmentsRequirements and Safety Before Each USE Inspect Your SAW Troubleshooting Guide for adjustment if necessary Dress for Safety Plan Your WorkInspect Your Workpiece USE Extra Caution with Large or ODD Shaped Workpieces When SAW is RunningDo not OVER-REACH Never cut freehand Basic SAW Operations Body and Hand Position FIG. UFinishing a cut Before freeing jammed material Sliding Carriage System FIG. W Miter CUT FIGBefore Leaving the SAW Compound CUT FIG. Z Bevel CUT FIG. Y To Slide Cut Wide Boards Fig. AA Cutting Bowed Material FIG. BBRough Cutting a Dado FIG. CC Fig. CC Bevel/Miter Settings Only When the Angle Between the Walls EqualsCutting Crown Molding FIG. GG, HH Outside corner-Left side KEY Bevel Miter Type of CUT SettingInside corner-Left side Inside corner-Right side Crown Molding Chart Lower Blade Guard MaintenanceMaintenance Replacing Carbon Brushes FIG Lubrication FIG. JJ, KK Debris from entering eyes when Removing sawdust from unitSawdust Wear proper eye protection to keep Troubleshooting Guide EYE Protection Parts List for SAW Schematic Parts List 4 in. Compound Miter SAW Model no Schematic Description Size Qty Parts List for Motor Sears Parts & Repair Service Center LE-FOYER MCSU-HOGAR R