HOW to Check and Adjust the Drive Brake

MAINTENANCE

HOW TO CHECK AND ADJUST THE DRIVE BRAKE

Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads. Adjust the drive brake as follows.

1.The location of the drive brake is on the right side of the gearbox (Figure 16).

2.Make sure the parking brake is set and the shift lever is in neutral (N). Turn the hex nut in a clockwise direction until the rear wheels do not turn when the unit is pushed forward.

3.Release the parking brake and push the unit. If the unit does not roll, turn the hex nut in a counterclockwise direction until the unit rolls.

4.Set the parking brake. Push the unit. If the rear wheels do not turn, the drive brake is correctly adjusted. Release the parking brake.

WARNING: If you cannot correctly adjust the drive brake, replace the brake pads. Correct replacement parts and assistance are available from an autho- rized service center.

Drive Brake

Gearbox	Hex Nut

Figure 16

HOW TO CHECK AND ADJUST THE CLUTCH

If the motion drive belt is loose, the clutch will slip when; (1) going up a hill, (2) pulling a heavy load, or (3) the unit will not move forward. Check the clearance at the rear of the pedal (Figure 17). If the motion drive belt is loose, the clearance will be less than 3/16 inch and the clutch will slip. Adjust the clutch as follows.

WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident.

1.Check the routing of the motion drive belt. Make sure the belt is installed correctly and is inside all the belt guides.

2.Disconnect the adjustable nut from the lever assembly (Figure 17).

3.Turn the adjustable nut counterclockwise to increase the length of the clutch rod. This adjustment will increase the clear- ance at the pedal and tighten the motion drive belt.

4.Assemble the adjustable nut to the lever assembly. Check the clearance at the pedal.

5.If the pedal cannot be set to 3/16 inch clearance, the motion drive belt has stretched and must be replaced. See “How To Replace The Motion Drive Belt”.

6.If the clutch still slips after the clutch has been adjusted, then the motion drive belt is damaged and must be replaced. See “How To Replace The Motion Drive Belt”.

7.After making an adjustment to the pedal, check the drive brake.

See “How To Check And Adjust The Drive Brake”.

F-040717L

Clutch Rod

Pedal

Lever

Assembly

Adjustable Nut (To increase the clearance, turn counterclockwise.)

3/16” (4.7mm)

Clearance

Figure 17

387002x92A specifications

Murray 387002x92A is a notable piece of equipment in the realm of power tools, designed to deliver exceptional performance and reliability for a variety of tasks. As a sophisticated model, it showcases numerous features and technologies that set it apart in the market.

One of its main features is the powerful motor, which ensures optimal performance for heavy-duty jobs. This motor is designed to generate substantial torque, making it suitable for both light and heavy applications. The lightweight build of the Murray 387002x92A also enhances its usability, allowing for easy maneuverability without sacrificing power. This combination of strength and ease of use makes it a favorite among both professionals and DIY enthusiasts.

Another significant characteristic of the Murray 387002x92A is its precision engineering. The design integrates advanced technology that allows for accurate cuts and operations, ensuring that users achieve the best possible results. This is particularly useful in projects that require meticulous attention to detail, as it minimizes the risk of error.

The tool incorporates state-of-the-art safety features, including slip-resistant grips and an emergency shut-off mechanism, which enhances user safety during operation. These safety measures are crucial for protecting users from accidents while ensuring that they can focus on their work without distraction.

Moreover, the Murray 387002x92A is built with durability in mind. The materials used in its construction are resistant to wear and tear, making it a long-lasting investment for users. This resilience ensures that the equipment can withstand tough working conditions and remain functional over time.

In terms of versatility, the Murray 387002x92A excels with its myriad of attachments and accessories that allow for a wide range of applications. Whether it's woodworking, metal fabrication, or other complex tasks, this model can adapt to meet various needs.

Maintenance is also simplified with the Murray 387002x92A, as its design facilitates easy cleaning and part replacement. This feature helps in prolonging the lifespan of the tool, keeping it in excellent condition for years to come.

In summary, the Murray 387002x92A stands out for its powerful performance, precision engineering, robust safety features, and impressive versatility. It is an ideal choice for those who seek a reliable and efficient tool capable of handling a diverse range of projects, making it a valuable addition to any toolbox.