HOW to Level the Mower Housing

MAINTENANCE

If the mower housing is level, the blade will cut easier and the lawn will look better.

WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the spark plug wire to prevent the engine from starting by accident.

1.Make sure the unit is on a hard level surface.

2.Check the air pressure in the tires. If the air pressure is incor- rect, the mower housing will not cut level. Make sure the tires are inflated to 14 PSI. (1 BAR).

3.Move the lever for the blade rotation control to the ENGAGE po- sition. Move the lift lever to the number “4” cutting height posi- tion.

4.There are two adjustment procedures below that will level the mower housing.

THE FRONT TO BACK ADJUSTMENT

Before the height of the mower housing is measured, understand that the position of the blades in the mower housing are not the same in the front as they are in the back.

There are measuring points on the mower housing indicated by small round dimples (or X marks) on the front and rear, left and right sides of the mower housing (Figure 22). To determine if an adjustment is needed, use a ruler and measure the distance from the level surface to the bottom of the mower housing. In correct adjustment, the front of the mower housing at point B will be from 0” to 1/2” (0 mm to 12 mm) higher than the back of the mower housing at point D.

SIDE VIEW

Measure from the bottom

of the mower housing.

LEVEL SURFACE

	D
	C	Figure 22
		Figure 22

F-040717L			27

1.Disconnect both adjuster rods from the adjuster rod brackets (Figure 23).

2.Turn the adjustable nut clockwise to lower the front or counter- clockwise to raise the front of the mower housing.

3.Connect the left adjuster rod to the adjuster rod bracket. Check the housing for the correct adjustment. Fasten the ad- justable nut with the washer and hair pin.

4.Repeat the above steps for the right side using the small round dimples (or X marks) at points A and C.

Adjuster Rod Bracket

Adjuster Rods

Figure 23

THE SIDE TO SIDE ADJUSTMENT

Use a ruler and measure the distance from the level surface to the bottom of the mower housing. Measure from the locations indicated by the small round dimples (or X marks) at points A and B. In correct adjustment, the mower housing at points A and B must be within 1/4” (6 mm) of the same height. If the difference in the measurement is more than 1/4” (6 mm), adjust as follows.

1.Disconnect the adjuster plate from the mower housing (Figure 24).

2.Move the adjuster plate to the front to raise or to the back to lower the side of the mower housing. On some adjuster plates the holes have numbers. To raise the mower housing, move to a higher number.

3.Connect the adjuster plate.

4.Check the housing for the correct adjustment. If necessary, re- peat the adjustment.

Adjuster Plate
Adjuster Plate	Figure 24

387002x92A specifications

Murray 387002x92A is a notable piece of equipment in the realm of power tools, designed to deliver exceptional performance and reliability for a variety of tasks. As a sophisticated model, it showcases numerous features and technologies that set it apart in the market.

One of its main features is the powerful motor, which ensures optimal performance for heavy-duty jobs. This motor is designed to generate substantial torque, making it suitable for both light and heavy applications. The lightweight build of the Murray 387002x92A also enhances its usability, allowing for easy maneuverability without sacrificing power. This combination of strength and ease of use makes it a favorite among both professionals and DIY enthusiasts.

Another significant characteristic of the Murray 387002x92A is its precision engineering. The design integrates advanced technology that allows for accurate cuts and operations, ensuring that users achieve the best possible results. This is particularly useful in projects that require meticulous attention to detail, as it minimizes the risk of error.

The tool incorporates state-of-the-art safety features, including slip-resistant grips and an emergency shut-off mechanism, which enhances user safety during operation. These safety measures are crucial for protecting users from accidents while ensuring that they can focus on their work without distraction.

Moreover, the Murray 387002x92A is built with durability in mind. The materials used in its construction are resistant to wear and tear, making it a long-lasting investment for users. This resilience ensures that the equipment can withstand tough working conditions and remain functional over time.

In terms of versatility, the Murray 387002x92A excels with its myriad of attachments and accessories that allow for a wide range of applications. Whether it's woodworking, metal fabrication, or other complex tasks, this model can adapt to meet various needs.

Maintenance is also simplified with the Murray 387002x92A, as its design facilitates easy cleaning and part replacement. This feature helps in prolonging the lifespan of the tool, keeping it in excellent condition for years to come.

In summary, the Murray 387002x92A stands out for its powerful performance, precision engineering, robust safety features, and impressive versatility. It is an ideal choice for those who seek a reliable and efficient tool capable of handling a diverse range of projects, making it a valuable addition to any toolbox.