Toro 1130 Maintainingyoursnowthrower, ShiftRodAdjustment, Skid Shoes, Carburetor, Lubrication

Page 12

ShiftRodAdjustment

To adjust the shift rod, proceed as follows:

•Remove the hairpin clip and slide the shift rod connector up, to separate the upper shift rod from the lower shift rod. See Figure 11.

•Place the shift lever into the sixth (6) position.

•Rotate the shift arm clockwise (from the operator's position) as faras it will go.

•Thread the upper shift rod downward until the

elbow on its lower end aligns with the hole found in the lower shift rod.

Skid Shoes

The space between the shave plate and the ground can be adjusted. See Figure 12.

•For close snow removal on a smooth surface, raise skid shoes higher on the auger housing.

•Use a middle or lower position when the area to be cleared is uneven.

_!!Shift Lever

Hairpin Clip_

\Upper Shift Rod

'pinClip

_Lower Shift Rod

Model 1028 Shown

Figure 11

•Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and sliding the shift rod connector back down into place.

IMPORTANT:Make certain to check for correct adjustment of the shift rod as instructed under Final Adjustments in the Assembly Section, before operating the snow thrower.

Carriage

Bolt

Flange

Nut

Skid

Shoe

Figure 12

thrower on gravel as loose gravel can be WARNING: Do not operate this snow easily picked up and thrown by the auger

causing injury to the operator and/or damage to the snow thrower.

•Adjust skid shoes by loosening the flange lock nuts and carriage bolts. Move skid shoes to desired position.

•Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes. Retighten nuts and bolts securely.

•Repeat on the other side of the snow thrower.

Carburetor

•Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude and load.

•Refer to the separate engine manual, packed with your unit, for carburetor adjustment information.

SECTION6: MAINTAININGYOURSNOWTHROWER

or inspecting, disengage all clutch levers

_ WARNING: Before lubricating, repairing, and stop engine. Wait until all moving

parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Always wear safety glasses during operation or while performing any adjustments or repairs.

Lubrication

Engine

Refer to the separate engine manual packed with your unit for all engine lubrication instructions.

WARNING: If any adjustments need to be made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of muffler, engine and other surrounding heated surfaces.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operators Manual Findingmodelnumber Importantsafeoperationpractices TrainingMaintenanceandstorage ItemsRequiredForAssembly BeforeAssemblyAssemblingyoursnowthrower AssemblingHandleClean-0utT001 KnowyoursnowthrowerPrimer Ignition KeyClean-0utTool HeatedHandlesSwitch Model1028SafetyIgnitionKey AugerDriveControlHeadlight TrackLockLeverBeforeStarting GasAnd0il Fill-upToEngageTrackDrive ToEngageAugersRecoil Starter Electric StarterDriftCutters Equipped Snow Thrower Model Drift Cutter Kit All models OEM-390-679Auger Makingadjustments ChuteAssemblyAugerControl DriveControlandShiftLeverShiftRodAdjustment MaintainingyoursnowthrowerSkid Shoes CarburetorHandle Panel Contro/IRods ........ICams Here EarlPinAuger Shaft Auger BearingsBeltRemovalAndReplacement ServicingyoursnowthrowerAugers ShavePlateandSkid ShoesReplacingFrictionWheelRubber Engine 0ff-Seas0nStorageTrack Friction Wheel Rubber HubTroubleshooting ProblemPARTSLISTFORMODELS1028 Models1028 Part DescriptionModel1028 784-5632B 11 a 19 -0528A Model1130 Model1130 Sup On engine 19 \ 18\ 710-0896 3334 Models1028&1130 \13 Part Description Page Manufacturers Limited Commercial Warranty For Manufacturers Limited Warranty for

1028, 1130 specifications

The Toro 1130 and 1028 snow throwers are robust machines designed to tackle winter's challenges with ease and efficiency. These models stand out for their power, innovative technologies, and user-friendly features, making them ideal choices for homeowners and professionals alike.

One of the primary features of both the Toro 1130 and 1028 is their powerful engine. The 1130 is equipped with a reliable 302cc engine, while the 1028 boasts a 250cc engine, providing ample power to clear deep snow quickly and effectively. The engines are designed for ease of starting, even in frigid temperatures, thanks to features like the electric start option.

Both models feature Toro's exceptional ClearOut technology, which enhances the snow throwers’ performance by improving the throwing distance and reducing clogging. This technology allows users to tackle heavy, wet snow and create a clear path efficiently. The 11-inch impeller and the rugged auger system are engineered to handle a variety of snow conditions, ensuring optimal clearing performance.

The Toro 1130 and 1028 are designed with user comfort in mind. Both models feature adjustable handle heights, allowing operators of different sizes to find the most comfortable position. The ergonomic handles are equipped with rubber grips that reduce fatigue during extended use. Additionally, their compact design makes them easy to maneuver in tight spaces, such as between cars and along walkways.

Another significant characteristic of these snow throwers is their intuitive controls. The one-hand operation feature allows users to easily control the chute direction and speed while managing the throttle. This functionality provides greater control and efficiency, allowing users to maintain focus on the task at hand.

Durability is also a hallmark of the Toro 1130 and 1028. Constructed from high-quality materials, these machines are built to withstand the rigors of winter. The heavy-duty housing and well-designed components ensure that they can handle tough conditions without compromising performance.

In summary, the Toro 1130 and 1028 snow throwers combine power, technology, and user-friendly features to deliver outstanding snow-clearing capabilities. With reliable engines, innovative throwing technology, ergonomic designs, and durability, these models are excellent choices for anyone looking to conquer winter's worst. Whether for residential or commercial use, Toro's commitment to quality makes these snow throwers a trusted option for snow management.
Top Page Image Contents