Toro 14AK81RK744, 14AQ81RP744 manual Battery, Cutting Deck Removal, Jump Starting, Charging

Page 27

IMPORTANT:When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT:Use a torque wrench to tighten the blade spindle hex flange nut to between 70 lbs-ft. and 90 lbs- ft.

Battery

California Proposition 65 Warning: Battery

posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

The battery is sealed and is maintenance-free. Acid levels cannot be checked and fluid can not be added.

•Always keep the battery cables and terminals clean and free of corrosive build-up.

•After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to both terminals

•Always keep the rubber boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery, disconnect the NEGATIVE (Black) wire from its terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire to the POSITIVE (+) terminal before connecting the NEGATIVE (Black) wire to the NEGATIVE (-) terminal. Be certain that the wires are connected to the correct terminals; reversing them could change the polarity and cause damage to your engine’s alternator.

Jump Starting

WARNING: Never jump start a damaged or frozen battery. Be certain the vehicles do not touch, and ignitions are off. Do not allow cable clamps to touch.

•Connect positive (+) cable to positive post (+) of your tractor’s discharged battery.

•Connect the other end of the (+) cable to the positive (+) post of the jumper battery.

•Connect the second negative (–) cable to the negative (–) post of the jumper battery.

•Make the final connection on the engine block of the stalled tractor, away from the battery. Attach to a unpainted part to assure a good connection.

IMPORTANT: If the jumper battery is installed on a vehicle (i.e. car, truck), do NOT start the vehicle’s engine when jump starting your tractor.

•Start the tractor (as instructed on page 16).

•Set the tractor’s parking brake before removing the jumper cables, in reverse order of connection.

•Allow the tractor’s engine to run for 15 minutes before shutting it off to allow the alternator time to charge the discharged battery.

Charging

If the unit has not been put into use for an extended period of time, charge the battery with an automotive- type 12-volt charger for a minimum of one hour at a maximum of six amps.

WARNING: Batteries give off an explosive gas while charging. Charge battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

Cutting Deck Removal

To remove the cutting deck, proceed as follows:

•Place the PTO/Blade Engage knob in the disengaged (OFF) position and engage the parking brake.

•Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

•Remove the deck belt from around the tractor’s electric PTO clutch (refer to Changing the Deck Belt).

•Looking at the cutting deck from the left side of the tractor, locate the deck support pin on the rear left side of the deck.

•Rotate the pin slightly toward the rear of the tractor and release it.

•Pull the deck support pin outward to release the deck from the deck lift arm. See Figure 21.

Support Pin

Figure 21

•Repeat the above steps on the tractor’s right side.

•Move the deck lift lever into the top notch to raise the deck lift arms up and out of the way.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents GT2200 & GT2300 Garden Tractors Table of Contents General Operation Important Safe Operation PracticesSlope Operation Children General Service Keep Hands and Feet Away from Rotating Parts Safety LabelsInstructional Labels — Slope GaugeTools Required Attaching the Battery CablesGas and Oil Fill-up Attaching The Steering WheelShipping Brace Removal Tire PressureGauge Wheels Know Your Garden Tractor Drive Pedal Ignition Switch ModuleThrottle Control Choke ControlElectric PTO Blade Engage Knob Cruise Control LeverParking Brake Lever Safety Interlock System Reverse Caution ModeOperating Your Garden Tractor Driving The Tractor Using the Deck Lift LeverStarting the Engine Stopping the EngineMoving The Tractor Manually Setting The Cruise ControlDriving On Slopes Engaging the Parking BrakeMowing Engaging the PTO BladesFront To Rear Making AdjustmentsSeat Adjustment Leveling the DeckSteering Adjustment Parking Brake AdjustmentChecking the Oil Level Maintaining Your Garden TractorEngine Engine OilRe-filling the Crankcase with Oil Changing the Engine OilDraining the Oil Changing the Oil FilterSpark Plugs PrecleanerService Paper Element Air FilterCleaning the Engine And Deck Hydrostatic TransmissionFuel Filter Pivot Points & Linkage LubricationEngine Front WheelsCutting Blades ServiceTires FuseCharging BatteryCutting Deck Removal Jump StartingChanging the Deck Belt Electric PTO Clutch OFF-SEASON Storage Maintenance Chart Trouble Possible Causes Corrective Action TroubleshootingHydrostatic Transmission SpecificationsPage MANUFACTURER’S Warranty Coverage Toro Company

14AK81RK744, 14AQ81RP744 specifications

The Toro 14AQ81RP744 and 14AK81RK744 are both exceptional lawn care machines designed to make maintaining your lawn easy and efficient. These models are well-regarded in the industry for their advanced features, durability, and user-friendly design.

The Toro 14AQ81RP744 is a powerful self-propelled lawn mower that boasts a 21-inch cutting deck, allowing it to cover considerable ground in minimal time. Equipped with a reliable OHV engine, it ensures efficient fuel combustion and impressive power, enabling it to tackle various grass types and conditions with ease. This model features a Personal Pace system, which automatically adjusts the mower's speed to match the operator's walking pace, providing an effortless mowing experience. Furthermore, the 14AQ81RP744 is equipped with a 3-in-1 cutting system, allowing users to choose between mulching, bagging, or side discharge.

Meanwhile, the Toro 14AK81RK744 model stands out with its innovative Recycler cutting technology. This feature finely shreds clippings, allowing them to decompose and return nutrients to the soil, ultimately promoting a healthier lawn. The 14AK81RK744 also sports a similarly robust engine and a 21-inch cutting width, making it perfect for both residential and commercial properties needing a dependable solution for lawn maintenance. Its lightweight design and folding handles make it a convenient choice for storage and transport.

Both models highlight Toro's commitment to user comfort and safety. The ergonomic handles ensure a comfortable grip during operation, while the adjustable cutting height feature enables users to customize their mow according to the specific needs of their lawn. Each mower is designed with an easy-start system, reducing the hassle of starting the engine.

In terms of technology, both Toro models excel in fuel efficiency and low emissions, aligning with modern environmental standards. The durable construction of these mowers ensures they can withstand the rigors of regular use, while also maintaining reliable performance over time.

In conclusion, the Toro 14AQ81RP744 and 14AK81RK744 are prime examples of efficient and effective lawn care solutions. With their powerful performance, advanced features, and thoughtful design, they are ideal for any homeowner or professional landscaper looking to achieve a beautifully maintained lawn.
Top Page Image Contents