Makita G3511R, G571O R, G5711R, G351O R, G341O R manual Safety Precautions

Page 9

1SAFETY PRECAUTIONS

AD O not operate the generator near gasoline or gaseous fuel because of the potential danger of explosion or fire.

Do not fill the fuel tank with fuel while the engine is running. Do not smoke or use open flame near the fuel tank. Be careful not to spill fuel during refueling. If fuel is spilt, wipe it off and let dry before starting the engine.

ADo not place inflammablesnear the generator.

Be careful not to place fuel, matches, gunpowder, oily cloths, straw, trash, or any other inflammables near the generator.

A D O not operate the generator inside a room, cave, tunnel, or other insuffi- ciently ventilated area. Always operate it in a well-ventilated area, otherwise the engine may become overheated, and the poisonous carbon monoxide gas contained in the exhaust gases will endanger human lives. Keep the gener- ator at least 1 meter (3 feet) away from any structure or building during use.

If the generator must be used indoors, the area must be well-ventilated and extreme caution must be taken regardingthe discharge of exhaust gases.

ADo not enclose the generator nor cover it with a box.

The generator has a built-in forced air cooling system, and may become overheated if it is enclosed. If generator has been covered to protect it from the weather during non use, be sure to remove it and keep it well away from the area during generator use.

AOperate the generator on a level surface.

It is not necessary to prepare a special foundation for the generator. However, the generator will vibrate on an irregular surface, so choose a level place without surface irregularities.

If the generator is tilted or moved during operation, fuel may spill and/or the generator may tip over, causing a hazardous situation.

Proper lubrication cannot be expected if the generator is operated on a steep incline or slope. In such a case, piston seizure may occur even if the oil is above the upper level.

A P a y attention to the wiring or extension cords from the generator to the connected device.

If the wire is under the generator or in contact with a vibrating part, it may break and possibly cause a fire, generator burnout, or electric shock hazard. Replace damaged or worn cords immediately.

ADo not operate in rain, in wet or damp conditions, or with wet hands.

The operator may suffer severe electric shock if the generator is wet due to rain or snow.

- 1 -

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model G341O R GeneratorPage California Emission Control Warranty Statement Limited Warranty What is not Covered Under this Warranty Repair and Replacement of EMISSION-RELATED Parts Page Contents Safety Precautions Page Specifications Components Check Engine OIL PRE-OPERATION ChecksCheck Engine Fuel Checking Component Parts Check Generator SurroundingsGrounding the Generator Page Starting the Engine Operating ProceduresStyle Precautions for Using the GFCl Receptacles Start SV I TCH Connectingto Domestic Circuits House Wiring Page Generator 4P-Receptacle Safety Precautions While Charging Fuse ReplacementDC Application OIL Sensor Stopping the GeneratorChecking the Operation HOW to USE Auto IdleWAlTAGE Information Voltage Drop in Electric Extension Cords Extension Cord ChartPeriodic Maintenance Maintenance Schedule0daily Engine OIL Change HOW-TO MaintenanceCleaning Fuel Strainer no Smoking Cleaning and Adjusting Spark PlugPreparation for Storage Troubleshooting Wiring Diagram G3510R ~za G571OR G5711R REC2 Fpsw MG, SW KeyswStarting Procedures BatteryElectric Starter Electric Starter G3511R, G5711RHOW to Install Battery Page Makita Corporation

G3511R, G341O R, G351O R, G5711R, G571O R specifications

Makita is renowned for its high-quality power tools, and the G5710R, G5711R, G3410R, G3511R, and G3510R models are no exception. These tools exemplify innovation, reliability, and superior performance, tailored to meet the needs of both professionals and DIY enthusiasts.

The Makita G5710R and G5711R models stand out for their robust construction and powerful motor capabilities. They are designed for heavy-duty applications, making them ideal for contractors or serious hobbyists who require maximum efficiency and longevity. Equipped with advanced cooling systems, these tools maintain optimal operating temperatures, thus prolonging motor life and enhancing performance. Additionally, the ergonomic design ensures comfortable handling, reducing fatigue during prolonged use.

Moving on to the G3410R and G3511R models, these tools feature a unique anti-vibration technology that minimizes operator fatigue while improving accuracy. This technology is particularly beneficial in tasks requiring precision, such as fine woodworking or intricate metalwork. The G3511R model comes specifically with an adjustable speed control, allowing users to tailor the speed for a variety of applications, whether it’s drilling into tough materials or delicate jobs that require finesse.

The G3510R model enhances user experience with its notable safety features, including automatic shut-off capabilities and overload protection. These features provide peace of mind for users, ensuring that they are safeguarded against potential mishaps during operation. Moreover, the inclusion of high-quality, durable materials in the design ensures that these tools can withstand the rigors of daily use in tough working environments.

In summary, the Makita G5710R, G5711R, G3410R, G3511R, and G3510R tools reflect the company’s commitment to excellence. With powerful motors, ergonomic designs, innovative technologies, and robust safety features, these models deliver unparalleled performance. Whether you’re a seasoned professional or an eager DIYer, investing in these tools means choosing reliability, efficiency, and advanced technology. As the market continues to evolve, Makita remains steadfast in providing top-notch solutions for every user's needs.
Top Page Image Contents