Makita G351O R, G571O R, G5711R, G341O R, G3511R manual WAlTAGE Information

Page 27

6. WAlTAGE INFORMATION

Some appliances need a "surge" of energy when starting. This means that the

amount of electrical power needed to start the appliance may exceed the amount needed to maintain its use. See the chart on page 15 for appliances you may use with this generator.

Electrical appliances and tools normally come with a label indicating voltage, cycles/Hz, amperage (amps) and electrical power needed to run the appliance or tool. Check with your nearest dealer or service center with questions regarding power surge of certain appliances or power tools.

Electrical loads such as incandescent lamps and hot plates require the same wattage to start as is needed to maintain use.

Loads such as fluorescent and mercury lamps require 1.2 to 2 times the indicated wattage during start-up.

Electrical motors require a large starting current. Power requirements depend on the type of motor and its use. Once enough "surge" is attained to start the motor, the appliance will require only 50% to 30% of the wattage to continue running.

Most electrical tools require 1.2 to 3 times their wattage for running under load during use. For example, a 5,000 watt generator can power a 1800 to 4000 watt electrical tool.

Loads such as submersible pumps and air compressors require a very large force to start. They need 3 to 5 times the normal running wattage in order to start. For example, a 5,000 watt generator would only be able to drive a 1,000 to 1,700 watt pump.

NOTE :

The following wattage chart is general guide only. Refer to your specific appliance for correct wattagle.

To determine the total wattage required to run a particular electrical appliance or

tool, mutiply the voltage figure of the appliance/tool by the amperage (amps) figure of same. The voltage and amperage (amps) information can be found on a name plate which is normally attached to electrical appliances and tools.

 

 

Applicable Wattage (W)

 

 

Applications

G2410R

 

G3510R

 

G5710R

 

 

G3511R

 

G5711R

 

 

 

 

 

 

 

60HZ

 

60HZ

 

60Hz

 

Incandescent lamp, heater

2,000

 

3,000

 

4.800

 

IFluorescent lamp, mercury lamp I

1,200

I

1,800

I

2,900

I

Electric tool

1,200

 

1,800

 

2,900

 

Pump, compressor

500

 

700

 

1,100

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model G341O R GeneratorPage California Emission Control Warranty Statement Limited Warranty What is not Covered Under this Warranty Repair and Replacement of EMISSION-RELATED Parts Page Contents Safety Precautions Page Specifications Components Check Engine OIL PRE-OPERATION ChecksCheck Engine Fuel Checking Component Parts Check Generator SurroundingsGrounding the Generator Page Starting the Engine Operating ProceduresStyle Precautions for Using the GFCl Receptacles Start SV I TCH Connectingto Domestic Circuits House Wiring Page Generator 4P-Receptacle Safety Precautions While Charging Fuse ReplacementDC Application OIL Sensor Stopping the GeneratorChecking the Operation HOW to USE Auto IdleWAlTAGE Information Voltage Drop in Electric Extension Cords Extension Cord ChartPeriodic Maintenance Maintenance Schedule0daily Engine OIL Change HOW-TO MaintenanceCleaning Fuel Strainer no Smoking Cleaning and Adjusting Spark PlugPreparation for Storage Troubleshooting Wiring Diagram G3510R ~za G571OR G5711R REC2 Fpsw MG, SW KeyswElectric Starter G3511R, G5711R BatteryStarting Procedures Electric StarterHOW to Install Battery Page Makita Corporation

G3511R, G341O R, G351O R, G5711R, G571O R specifications

Makita is renowned for its high-quality power tools, and the G5710R, G5711R, G3410R, G3511R, and G3510R models are no exception. These tools exemplify innovation, reliability, and superior performance, tailored to meet the needs of both professionals and DIY enthusiasts.

The Makita G5710R and G5711R models stand out for their robust construction and powerful motor capabilities. They are designed for heavy-duty applications, making them ideal for contractors or serious hobbyists who require maximum efficiency and longevity. Equipped with advanced cooling systems, these tools maintain optimal operating temperatures, thus prolonging motor life and enhancing performance. Additionally, the ergonomic design ensures comfortable handling, reducing fatigue during prolonged use.

Moving on to the G3410R and G3511R models, these tools feature a unique anti-vibration technology that minimizes operator fatigue while improving accuracy. This technology is particularly beneficial in tasks requiring precision, such as fine woodworking or intricate metalwork. The G3511R model comes specifically with an adjustable speed control, allowing users to tailor the speed for a variety of applications, whether it’s drilling into tough materials or delicate jobs that require finesse.

The G3510R model enhances user experience with its notable safety features, including automatic shut-off capabilities and overload protection. These features provide peace of mind for users, ensuring that they are safeguarded against potential mishaps during operation. Moreover, the inclusion of high-quality, durable materials in the design ensures that these tools can withstand the rigors of daily use in tough working environments.

In summary, the Makita G5710R, G5711R, G3410R, G3511R, and G3510R tools reflect the company’s commitment to excellence. With powerful motors, ergonomic designs, innovative technologies, and robust safety features, these models deliver unparalleled performance. Whether you’re a seasoned professional or an eager DIYer, investing in these tools means choosing reliability, efficiency, and advanced technology. As the market continues to evolve, Makita remains steadfast in providing top-notch solutions for every user's needs.
Top Page Image Contents