Murray 11053x92a manual Service and Adjustment, HOW to Remove and Install the Tines, Tine Removal

Page 18

SERVICE AND ADJUSTMENT

HOW TO REMOVE AND INSTALL THE TINES

References to the right or left side of the cul- tivator are from the viewpoint of the opera- tor’s position behind the unit.

All four tines are different and cannot be in- terchanged. The tines must be correctly installed or the cultivator will not function properly.

To till around plants or in small areas, the outside tines can be removed to reduce the tilling width to approximately 7 inches.

WARNING: The tines are self sharpening and will become quite sharp from use. Handle

carefully.

The tines will all wear evenly. If the tines are being replaced because of wear, we recom- mend that all four tines be replaced at the same time. To replace the tines, do the fol- lowing:

Tine Removal

1.Put the on-off switch in the OFF posi- tion.

2.Disconnect the spark plug wire from the spark plug.

3.While wearing gloves, remove the hair- pins and clevis pins that secure the tine assemblies to the shaft (see Figure 13). Remove the tines from one side of the unit.

Clevis

Pins

Tine Installation

1.Clean and lubricate the tine shaft with a few drops of oil.

2.Place the inside tine on the tine shaft and reinstall the clevis pin and hairpin.

3.When the tines are properly installed, the letter R will be visible on the outside of the right tine (see Figure 14). The letter L will be visible on the outside of the left tine.

R

Figure 14

4.Mount the outside tine on the tine shaft and fasten with the clevis pin and hair- pin (see Figure 13).

5.The cutting tips on the outside tines all bend in toward the inside tine. When as- sembled correctly, the letter R on the right side, or L on the left side, will be visible from the outside of the unit.

6.Repeat the above steps on the opposite side of the unit.

NOTE: Make sure the tines are installed on the correct side of the unit.

Hair Pins

Tines

Figure 13

 

 

F-051302L

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model MURRAY, INC. Two Year Limited Warranty OWNER’S Information Responsibility of the OwnerOperating Safety Safety RulesFuel Safety Safe Operation Practices for CultivatorRepair / Adjustments Safety Safe StorageInternational Symbols Slow Fast Fuel Oil Choke OFF Half Choke Full ChokeHOW to Remove the Cultivator from the Carton AssemblyAssembly Parts Packed Separately in Carton HOW to Assemble the HandleOutside of the lower handle as you Tighten the knobsDle and damage the engine casing Checklist Operation Know Your CultivatorEYE Protection How To Stop The Cultivator HOW to USE the CultivatorHOW to Operate the Cultivator How To Set The Depth Rod And WheelsFuel Mixture Chart mixture SI. Metric How To Prepare The EngineHow To Mix The Fuel Mixture Before Starting the EngineHOW to Start the Engine Light cultivation with moderate growth To 2 inches depth Hints for Depth ROD or Wheel AdjustmentCultivating Tips Seed bed preparation 4 to 6 inches depthCustomer Responsibilities MaintenanceProduct Specifications General RecommendationsLubrication Remove the air vent screw see FigureMent spark plug Filter cover and the air filterTine Installation Service and AdjustmentHOW to Remove and Install the Tines Tine RemovalHOW to Adjust the Carburetor Engine Shown With Fuel Tank RemovedStorage CultivatorEngine Trouble Shooting Chart Trouble Cause CorrectionModel 11053x92A KEY 485 483 323393A 480 482 484 493 481 490 496 492 494 495 491 660 650 661 662 663 946 950930 948 943 051302L HOW to Order Repair Parts MURRAY, INC. Lawn Mower Central Parts Distributors

11053x92a specifications

The Murray 11053x92a is a standout model that excels in various applications, making it a valuable asset in both residential and commercial settings. This model combines innovative technology and robust design, tailored to meet the demands of modern users.

One of the main features of the Murray 11053x92a is its powerful engine. Equipped with a high-performance motor, this model ensures efficient operation and a high level of reliability. The engine's design emphasizes fuel efficiency, allowing for extended usage without frequent refueling. This is particularly advantageous for lawn care professionals and homeowners alike, as it helps save time and reduces operational costs.

The cutting deck of the Murray 11053x92a is another highlight. With a generous cutting width, it delivers an expansive coverage area, allowing users to complete their tasks more quickly. The adjustable cutting height feature lets users customize grass length, accommodating various lawn conditions and personal preferences. This versatility makes it suitable for tackling both well-maintained lawns and overgrown areas.

In terms of technology, the Murray 11053x92a incorporates user-friendly features that enhance the overall experience. Its easy-start ignition system ensures quick starts with minimal effort, eliminating frustration associated with manual pull-starts. Additionally, the ergonomic handle design provides comfort and control during operation, reducing user fatigue during extended use.

Safety is a paramount consideration in the design of the Murray 11053x92a. It comes equipped with a blade brake system that automatically stops the blade when the operator releases the handle, minimizing the risk of accidents. This feature is especially important for families with children or pets playing nearby.

Moreover, the model’s construction emphasizes durability. Built with high-quality materials, it can withstand the rigors of tough mowing conditions. Its robust frame is designed to resist rust and corrosion, ensuring longevity and maintaining aesthetic appeal over time.

In summary, the Murray 11053x92a is distinguished by its powerful engine, versatile cutting deck, user-friendly features, safety mechanisms, and durable construction. These characteristics make it a reliable choice for anyone in need of an efficient and effective mowing solution, whether for residential lawns or larger commercial properties.
Top Page Image Contents