Murray 11052x92D manual Lubrication, Remove the air vent screw see Figure

Page 16

MAINTENANCE

LUBRICATION

Every 25 hours and/or at the beginning of each season, make sure the gear box is filled with lubricant (see Figure 9). Tubes of gear lubricant are available from most auto- motive supply stores. Use portable tool grease such as Lubriplate 630AA (Product No. 06787, 1–3/4 oz. tube) or Lubriplate GR–132 (Product No. 15892, 10 oz. tube).

After cleaning and before storage, apply oil to the tine shaft (see Figure 9).

WARNING: Allow the transmis- sion to cool before filling with grease.

1.Remove both left side tines. See “How To Replace The Tines” in the Service and Adjustments section.

2.Remove the air vent screw (see Figure 9).

3.Mount a grease gun onto the grease fit- ting. Fill the transmission until the grease begins to come out of the air vent screw hole.

4.Reinstall the air vent screw.

5.Check the condition of the felt washer (see Figure 9). Replace the felt washer

if it is damaged (see the Repair Parts section in this manual).

6.Clean and lubricate the tine shaft with a few drops of oil.

7.Reinstall the left side tines.

8.Remove the right side tines. Check the felt washer for damage. Clean and oil the tine shaft. Reinstall the right side tines.

Air Vent Screw

Tine

Shaft

Felt

Washer

Grease FittingFigure 9

HOW TO CLEAN THE TINES

Always remove dirt and debris from the culti- vator after each use. Remove any string, wire or vegetation that may become lodged in the mechanism and stop the tines from rotating.

1.Release the throttle control and move the on–off switch to the OFF position. Disconnect the spark plug wire from the spark plug.

2.While wearing gloves, remove the hair- pins and clevis pins that secure the tine assemblies to the shaft (see Figure 10). Remove the tines from the shaft.

3.Remove any lodged debris from the shaft and tines. Clean and lubricate the tine shaft with a few drops of oil.

4.Reassemble the tines on the shaft and

secure with a clevis pin and hairpin.

16

F–031305L

5.Connect the spark plug wire to the spark plug.

Clevis

Pins

Hair Pins

Tines

Figure 10

 

 

Image 16
Contents Model MURRAY, INC. Two Year Limited Warranty OWNER’S Information Responsibility of the OwnerSafety Rules Operating SafetyFuel Safety Safe Operation Practices for CultivatorRepair / Adjustments Safety Safe StorageInternational Symbols Slow Fast Fuel Oil Choke OFF Half Choke Full ChokeAssembly Assembly Parts Packed Separately in CartonHOW to Remove the Cultivator from the Carton HOW to Assemble the HandleTighten the knobs Outside of the lower handle as youDle and damage the engine casing Checklist Know Your Cultivator OperationEYE Protection HOW to USE the Cultivator HOW to Operate the CultivatorHow To Stop The Cultivator How To Set The DepthHow To Mix The Fuel Mixture How To Prepare The EngineBefore Starting the Engine These areas HOW to Start the EngineNo Choke Half Choke Full Choke Choke Control Hints for Depth Stake or Wheel Adjustment Cultivating TipsSeed bed preparation 4 to 6 inches depth Heavy soil 4 inch depth or greaterMaintenance Product SpecificationsCustomer Responsibilities General RecommendationsLubrication Remove the air vent screw see FigureMent spark plug Filter cover and the air filterService and Adjustment HOW to Remove and Install the TinesTine Installation Tine RemovalHOW to Adjust the Carburetor Engine Shown With Air Filter RemovedCultivator StorageEngine Trouble Shooting Chart Trouble Cause CorrectionModel 11052x92D KEY 485 483 323393A 480 482 484 493 481 490 496 492 494 495 491 660 650 661 662 663 946 950930 948 943 031305L HOW to Order Repair Parts MURRAY, INC. Lawn Mower Central Parts Distributors