Murray 11052x92D manual Service and Adjustment, HOW to Remove and Install the Tines, Tine Removal

Page 18

SERVICE AND ADJUSTMENT

HOW TO REMOVE AND INSTALL THE TINES

References to the right or left side of the cul- tivator are from the viewpoint of the opera- tor’s position behind the unit.

All four tines are different and cannot be in- terchanged. The tines must be correctly installed or the cultivator will not function properly.

To till around plants or in small areas, the outside tines can be removed to reduce the tilling width to approximately 7 inches.

WARNING: The tines are self sharpening and will become quite sharp from use. Handle

carefully.

The tines will all wear evenly. If the tines are being replaced because of wear, we recom- mend that all four tines be replaced at the same time. To replace the tines, do the fol- lowing:

Tine Removal

1.Put the on–off switch in the OFF posi- tion.

2.Disconnect the spark plug wire from the spark plug.

3.While wearing gloves, remove the hair- pins and clevis pins that secure the tine assemblies to the shaft (see Figure 13). Remove the tines from one side of the unit.

Clevis

Pins

Tine Installation

1.Clean and lubricate the tine shaft with a few drops of oil.

2.Place the inside tine on the tine shaft and reinstall the clevis pin and hairpin.

3.When the tines are properly installed, the letter R will be visible on the outside of the right tine (see Figure 14). The letter L will be visible on the outside of the left tine.

R

Figure 14

4.Mount the outside tine on the tine shaft and fasten with the clevis pin and hair- pin (see Figure 13).

5.The cutting tips on the outside tines all bend in toward the inside tine. When as- sembled correctly, the letter R on the right side, or L on the left side, will be visible from the outside of the unit.

6.Repeat the above steps on the opposite side of the unit.

NOTE: Make sure the tines are installed on the correct side of the unit.

Hair Pins

Tines

Figure 13

 

 

F–031305L

18

Image 18
Contents Model MURRAY, INC. Two Year Limited Warranty OWNER’S Information Responsibility of the OwnerFuel Safety Safety RulesOperating Safety Safe Operation Practices for CultivatorRepair / Adjustments Safety Safe StorageInternational Symbols Slow Fast Fuel Oil Choke OFF Half Choke Full ChokeHOW to Remove the Cultivator from the Carton AssemblyAssembly Parts Packed Separately in Carton HOW to Assemble the HandleOutside of the lower handle as you Tighten the knobsDle and damage the engine casing Checklist Operation Know Your CultivatorEYE Protection How To Stop The Cultivator HOW to USE the CultivatorHOW to Operate the Cultivator How To Set The DepthHow To Prepare The Engine How To Mix The Fuel MixtureBefore Starting the Engine HOW to Start the Engine These areasNo Choke Half Choke Full Choke Choke Control Seed bed preparation 4 to 6 inches depth Hints for Depth Stake or Wheel AdjustmentCultivating Tips Heavy soil 4 inch depth or greaterCustomer Responsibilities MaintenanceProduct Specifications General RecommendationsLubrication Remove the air vent screw see FigureMent spark plug Filter cover and the air filterTine Installation Service and AdjustmentHOW to Remove and Install the Tines Tine RemovalHOW to Adjust the Carburetor Engine Shown With Air Filter RemovedStorage CultivatorEngine Trouble Shooting Chart Trouble Cause CorrectionModel 11052x92D KEY 485 483 323393A 480 482 484 493 481 490 496 492 494 495 491 660 650 661 662 663 946 950930 948 943 031305L HOW to Order Repair Parts MURRAY, INC. Lawn Mower Central Parts Distributors