Weed Eater MX550 Cutting Methods, Tip of line does, Cutting Work area, Inches 8 cm above ground

Page 8

Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or as- phalt can cause excessive wear to the trimmer head. If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to ob- tain the most efficient line length.

WARNING: Use only 0.080(2 mm) diameter line. Other sizes of line will not ad- vance properly and can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

SThe tip of the line does the cutting. You will achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

Tip of line does

Line crowded into

the cutting.

work area.

RightWrong

S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences.

SFor trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

S During light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence

wire.

SFor mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

3 inches (8 cm) above ground

SCALPING -- The scalping technique re- moves unwanted vegetation. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique in- creases line wear.

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

SWEEPING -- The fanning action of the rotat- ing line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side.

8

Image 8
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules Operator SafetyUnit / Maintenance Safety Fuel SafetyCutting Safety Transporting and StorageAssembly Adjusting the HandleOperation Attaching ShieldStop Switch HOW to Stop Your UnitHOW to Start Your Unit Primer BulbStarting a Warm Engine Starting a Flooded EngineOperating Position Trimmer Line AdvanceCutting Methods Tip of line doesCutting Work area Inches 8 cm above groundMaintenance Service and Adjustments Carburetor Idle Speed AdjustmentReplacing the Line Replacing the Cutting HeadSeasonal Storage Fuel SystemEngine OtherTroubleshooting Table Cause Remedy Limited Warranty Canada, contactIntermediate 125 hours Extended 300 hours

545186834, MX550 specifications

The Weed Eater MX550, model number 545186834, is a powerful and efficient string trimmer designed for both residential and light commercial use. This reliable tool is engineered to provide excellent cutting performance, ease of use, and versatility, catering to various lawn care needs.

One of the standout features of the MX550 is its robust 25cc two-cycle engine. This powerful engine ensures optimal performance, allowing users to tackle tough grass, weeds, and overgrown areas with ease. The engine delivers impressive power while remaining lightweight, which minimizes operator fatigue during extended use.

The MX550 is equipped with a 16-inch cutting swath that efficiently covers large areas in a short amount of time, making it ideal for homeowners or landscapers with sizable properties. This wider cutting path allows users to reduce the time spent trimming, thereby increasing productivity. The tool is compatible with both regular trimmer line and heavy-duty line, catering to different cutting scenarios based on user preference.

Innovative technology is featured in the MX550 with its easy-to-load, bump-feed head. This design simplifies line replacement, allowing users to quickly and efficiently reload the trimmer line without the frustration often associated with traditional systems. The bump-feed function eliminates downtime, ensuring that the trimmer is always ready for action.

Moreover, the Weed Eater MX550 comes with adjustable handlebars, providing a comfortable grip for users of all heights. This ergonomic feature enhances control and maneuverability, making it easier to work in tight spaces or navigate around obstacles such as trees and flower beds.

This model also prioritizes user safety and convenience. It features a clear debris shield that protects the operator from debris while providing a clear view of the cutting area. The trimmer’s balanced design and lightweight frame reduce strain on the user, making it an ideal choice for extended periods of operation.

Additionally, the MX550 is designed for easy maintenance, with accessible components that allow for straightforward cleaning and servicing. This ensures the longevity of the trimmer, keeping it in peak operating condition for years to come.

In summary, the Weed Eater MX550, 545186834, combines power, versatility, and user-oriented design features to create an effective string trimmer for a range of trimming tasks. Whether you are a homeowner looking to maintain your lawn or a professional landscaper seeking reliable equipment, the MX550 stands out as a dependable choice in the vast market of outdoor power tools.