Weed Eater BC3150, 530165748-01 instruction manual Assembly

Page 4

equipped with a spark arresting screen. If you operate in a locale where such regulations ex- ist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal

homeowner use, the muffler and spark arrest- ing screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your autho- rized service dealer.

ASSEMBLY

CARTON CONTENTS

Check carton contents against the following list:

SBrushcutter

SCupped washer

SLarge nut for installing blades S Hex wrench

S Handlebar

S Bracket cover

S Bracket cover screws (2) S Metal blade shield

S Blade shield screws (4) S 4--point weed blade

S Plastic shield

S Wing nut (screwed onto plastic shield) S Shoulder strap with warning

S Container of oil

WARNING: Always stop unit and dis- connect spark plug before performing any as- sembly procedures.

WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure.

Examine parts for damage. Do not use dam- aged parts.

NOTE: If you need assistance or find parts missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

TOOLS REQUIRED

SHex wrench (provided) S Adjustable wrench

S Phillips screwdriver

ATTACHING THE HANDLEBAR

DANGER: To avoid serious injury, the barrier portion of the handlebar must be installed

Handlebar Screw

Bracket Cover

Mounting

Bracket

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit.

1. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger

sign is on your back and the hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the shoulder.

2. Adjust the strap, allowing the hook to be about 6 inches (15 cm) below the waist.

3. Fasten the strap hook to the clamp located between the trigger handle and the handle- bar clamp base and lift the tool to the oper- ating position.

4. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation.

NOTE: It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit.

TO RELOCATE SHOULDER STRAP CLAMP:

1.Loosen and remove both clamp screws.

2.Place the upper shoulder strap clamp over the shaft.

3.Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes.

as shown to provide a barrier between operator and the spinning blade.

1.Locate the decal on the handlebar. This decal includes an arrow. Position the handlebar with the mounting bracket at the end of the arrow.

2.Position the bracket cover over the han- dlebar. Again make sure the handlebar is at the end of the arrow.

3.Insert screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench.

Lower Shoulder Strap Clamp

Upper Shoulder

Strap Clamp

Screws

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Manual de Instrucciones Manuel d’Instructions 11/19/04Safety Rules Operator SafetyHazard Zone Leg protectionUNIT/MAINTENANCE Safety Fuel SafetyCutting Safety Transporting and StorageAssembly Assembly Information Trimmer Head Configuring Your UnitAttaching the Plastic Shield and Trimmer Head Assembly Information Weed Blade Installation of the Metal BladeAttaching the Metal Shield Washer Cupped NutOperation HOW to Stop Your Unit HOW to Start Your UnitSwitch Throttle Trigger See the Storage section for additional in- formationStarting a Warm Engine Starting a Flooded EngineOperating Position Operating Instructions for USE with Trimmer HeadCutting Methods Operating Instructions for USE with Weed BladeMaintenance Inspect and Clean Unit and DE- CalsCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsService and Adjustments Seasonal Storage Fuel SystemEngine OtherTroubleshooting Table Cause Remedy Ligations The U.S. Environmental Limited WarrantyTies As the small off--road engine engine Intermediate 125 hours Extended 300 hours

530165748-01, BC3150 specifications

The Weed Eater 530165748-01, BC3150 is an innovative and efficient string trimmer designed for both residential and professional landscaping needs. Known for its reliable performance, the BC3150 embodies a blend of power, versatility, and user-friendly design.

One of the standout features of the BC3150 is its powerful 31cc two-stroke engine. This engine provides robust cutting capability, making it suitable for a variety of tasks including trimming, edging, and clearing overgrown areas. The high-performance engine ensures that users can tackle tough weeds and grass with ease, providing a clean and professional finish in less time.

The BC3150 comes equipped with a dual-line bump feed head, which allows users to quickly advance new line simply by tapping the head on the ground. This feature saves time and effort, allowing for uninterrupted work and enhanced productivity. The dual-line system also provides improved cutting efficiency, ensuring that users can maintain well-manicured lawns and gardens.

Weed Eater has incorporated advanced technology into the design of the BC3150 for added convenience and comfort. The trimmer features an ergonomic handle that reduces fatigue during prolonged use. Additionally, the adjustable harness distributes weight evenly, providing greater balance and control, which is essential for large-scale landscaping projects.

One of the notable characteristics of the Weed Eater BC3150 is its lightweight construction. Weighing in at just under 10 pounds, this string trimmer is easy to maneuver and transport. This makes it an ideal choice for both novice and experienced users who require a reliable tool without the burden of excessive weight.

Durability is another key aspect of the BC3150’s design. Constructed with high-quality materials, the trimmer is built to withstand rigorous use over time. Its robust build ensures that it can handle various weather conditions and outdoor environments, making it a long-term investment for lawn care.

The Weed Eater BC3150 is versatile enough to accommodate various attachments, expanding its functionality. Users can easily switch between different heads for tasks such as edging or brush cutting, further enhancing its utility.

Overall, the Weed Eater 530165748-01, BC3150 is a powerful, efficient, and user-friendly string trimmer that meets the demands of any landscaping job. With its combination of advanced features, durability, and lightweight design, it's an excellent choice for anyone looking to maintain their outdoor spaces with ease.
Top Page Image Contents