Weed Eater 530165748-01, BC3150 instruction manual Operation

Page 7

8.Insert a small screwdriver into aligned holes. This will keep the shaft from turn- ing while tightening the blade nut.

Screwdriver

9.TIghten blade nut firmly with a wrench while holding screwdriver in position.

10.Remove the screwdriver.

11.Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must re- install.

NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and re- move parts. Be sure to store parts and instruc- tions for future use.

OPERATION

KNOW YOUR UNIT

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

 

 

Handlebar

Trimmer Head

Shaft

 

Line Limiter

ON/OFF Switch

Shield

Blade

 

 

 

Starter Handle

 

 

Primer Bulb

 

Throttle Trigger

 

Blade

 

 

 

Choke

Muffler

 

Lever

 

 

ON/OFF SWITCH

The ON/OFF switch is located on the trigger handle and is used to stop the engine. Move the switch to the OFF position to stop the engine.

PRIMER BULB

The PRIMER BULB removes air from the car- buretor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form.

CHOKE

The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. After the engine attempts to start, move the choke lever to the HALF CHOKE position. Once engine has started, move the choke lever to the OFF CHOKE position.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel information in the safety rules before you be- gin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gaso-

7

Image 7
Contents 11/19/04 Manual de Instrucciones Manuel d’InstructionsLeg protection Safety RulesOperator Safety Hazard ZoneTransporting and Storage UNIT/MAINTENANCE SafetyFuel Safety Cutting SafetyAssembly Assembly Information Trimmer Head Configuring Your UnitAttaching the Plastic Shield and Trimmer Head Washer Cupped Nut Assembly Information Weed BladeInstallation of the Metal Blade Attaching the Metal ShieldOperation See the Storage section for additional in- formation HOW to Stop Your UnitHOW to Start Your Unit Switch Throttle TriggerOperating Instructions for USE with Trimmer Head Starting a Warm EngineStarting a Flooded Engine Operating PositionOperating Instructions for USE with Weed Blade Cutting MethodsCheck for Damaged or Worn Parts MaintenanceInspect and Clean Unit and DE- Cals Check for Loose Fasteners and PartsService and Adjustments Other Seasonal StorageFuel System EngineTroubleshooting Table Cause Remedy Ligations The U.S. Environmental Limited WarrantyTies As the small off--road engine engine Intermediate 125 hours Extended 300 hours

530165748-01, BC3150 specifications

The Weed Eater 530165748-01, BC3150 is an innovative and efficient string trimmer designed for both residential and professional landscaping needs. Known for its reliable performance, the BC3150 embodies a blend of power, versatility, and user-friendly design.

One of the standout features of the BC3150 is its powerful 31cc two-stroke engine. This engine provides robust cutting capability, making it suitable for a variety of tasks including trimming, edging, and clearing overgrown areas. The high-performance engine ensures that users can tackle tough weeds and grass with ease, providing a clean and professional finish in less time.

The BC3150 comes equipped with a dual-line bump feed head, which allows users to quickly advance new line simply by tapping the head on the ground. This feature saves time and effort, allowing for uninterrupted work and enhanced productivity. The dual-line system also provides improved cutting efficiency, ensuring that users can maintain well-manicured lawns and gardens.

Weed Eater has incorporated advanced technology into the design of the BC3150 for added convenience and comfort. The trimmer features an ergonomic handle that reduces fatigue during prolonged use. Additionally, the adjustable harness distributes weight evenly, providing greater balance and control, which is essential for large-scale landscaping projects.

One of the notable characteristics of the Weed Eater BC3150 is its lightweight construction. Weighing in at just under 10 pounds, this string trimmer is easy to maneuver and transport. This makes it an ideal choice for both novice and experienced users who require a reliable tool without the burden of excessive weight.

Durability is another key aspect of the BC3150’s design. Constructed with high-quality materials, the trimmer is built to withstand rigorous use over time. Its robust build ensures that it can handle various weather conditions and outdoor environments, making it a long-term investment for lawn care.

The Weed Eater BC3150 is versatile enough to accommodate various attachments, expanding its functionality. Users can easily switch between different heads for tasks such as edging or brush cutting, further enhancing its utility.

Overall, the Weed Eater 530165748-01, BC3150 is a powerful, efficient, and user-friendly string trimmer that meets the demands of any landscaping job. With its combination of advanced features, durability, and lightweight design, it's an excellent choice for anyone looking to maintain their outdoor spaces with ease.