Parasound Zamp v.3 manual Front Panel Controls and Indicators

Page 9

FRONT PANEL CONTROLS AND INDICATORS

7

 

 

 

Power Button

Press the Power button once to turn the Zamp v.3 on, press it again to turn it off.

Note: The Power button is inoperative when the Auto On switch is set to Audio or 12V.

L and R Channel Indicators

L and R will illuminate green when the Zamp v.3 is turned on and is operating normally. The green L or R indicator will not light if the fault condition is only in that channel. Neither L or R will illuminate if there is a general fault or if the temperature is too high.

Protect L R Hi-Temp

Power

Zamp v.3 Zone Amplifier

Protect Indicator

Protect will illuminate red when the Zamp v.3 has experienced either an internal or external fault condition which has also activated its protection circuit to prevent internal damage.

Note: It is normal for Protect to flash on for 1 – 2 seconds after the unit is turned on.

Hi-Temp Indicator

Hi-Temp will illuminate red when the Zamp v.3 reaches its maximum safe operating temperature. If the heat persists the unit will soon shut itself off for protection and will remain off until the temperature drops. If Hi-Temp appears, the unit has been over-driven at too high a listening level and/or too low impedance speaker load or has not been provided with sufficient ventilation.

Headphone Jack

The headphone jack on the front panel accepts a 1⁄8" (3.5 mm) plug. Its high current headphone circuit will easily drive headphones with an impedance of 8 Ω or higher. The output to the speaker terminals is disconnected when you plug headphones into the Zamp v.3.

Maintaining Your Zamp v.3

Your Parasound Zamp v.3 power amplifier requires no periodic maintenance other than to receive an occasional flattering remark. It has no user-serviceable parts inside. To avoid the risk of electric shock, do not remove its top cover. The exterior can be cleaned with a soft cloth pre-moistened only with a few drops of water or glass cleaner.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents N e a m p l i f i e r Important Safety Instructions Table of Contents Unpacking Introduction115v 230v AC Voltage Selector Switch Installation and Ventilation RequirementsRack Mounting Rear Panel Connections and Controls Mono Operation Mono Input and Speaker ConnectionsAutomatic Turn On Options AC Power Connections and AC Grounding Gnd Ground Lift Switch12V In Connection 12V Trigger Out ConnectionFront Panel Controls and Indicators No sound Typical Problems and RemediesBackground Hum Distorted and Weak SoundIf YOU Require Assistance Before You Return Any Unit to Parasound for ServiceParasound Zamp V.3 Specifications

Zamp v.3 specifications

The Parasound Zamp v.3 is a compact yet powerful amplifier designed to deliver excellent audio performance in a variety of settings. Known for its high-quality construction and audiophile-grade sound, the Zamp v.3 is particularly appealing to those who seek a reliable amplifier for smaller spaces or as part of a multi-room audio system.

One of the standout features of the Zamp v.3 is its robust power output. With 50 watts per channel into 8 ohms and 75 watts per channel into 4 ohms, this amplifier is capable of driving a wide range of speakers, making it a versatile choice for both home theaters and stereo setups. The unit's Class A/B operation ensures that the sound remains clean and dynamic, providing an immersive listening experience.

The Zamp v.3 also integrates advanced technological features that enhance its functionality. The amplifier is equipped with a high-current power supply that ensures efficient power delivery, reducing distortion even when pushed to higher volume levels. Its dual-transformer design further contributes to the amplifier's ability to deliver sustained sonic performance without sacrificing fidelity.

Additionally, the Zamp v.3 showcases a number of thoughtful design elements aimed at user convenience. It features both unbalanced RCA and balanced XLR inputs, allowing for easy integration into existing audio systems. The rear panel includes a switched AC outlet, making it easy to connect and power other devices, such as source components, without needing multiple outlets.

Another noteworthy characteristic of the Zamp v.3 is its compact size, which allows it to be easily placed on shelves or in tight spaces. Despite its smaller footprint, the amplifier maintains a rugged build quality that ensures durability and long-term reliability.

For added flexibility, the Zamp v.3 incorporates automatic turn-on/off circuitry, making it energy-efficient and user-friendly. This feature allows the amplifier to power down when not in use, reducing energy consumption and extending the lifespan of the unit.

In conclusion, the Parasound Zamp v.3 is an impressive amplifier that combines power, advanced technology, and user-friendly features. Its ability to deliver high-quality sound in a compact form makes it an attractive option for audiophiles and casual listeners alike. Whether used in a simple stereo setup or as part of a larger multi-room system, the Zamp v.3 stands out as a reliable choice that meets the demands of modern audio environments.
Top Page Image Contents