Electrolux 295 manual Chain Brake, Braking function control, Inertia activating function control

Page 9

IGNITION SWITCH

(START) ON

 

 

 

 

OFF (STOP)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHOKE/FAST IDLE

(SIDE VIEW)

Choke/Fast Idle OFF FULL

Lever

For a warm engine:

SPull the choke/fast idle lever out to the full extent; then, push the choke/fast idle lever back to the OFF position. This will

set the fast idle lock to the start position.

SPull the starter rope quickly with your

right hand until the engine starts.

SSqueeze and release the throttle trigger to release the fast idle lock, allowing en- gine to idle.

Difficult starting or flooded engine:

The engine may be flooded with too much fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ignition switch is in the ON or START position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start refer to the troubleshooting chart or call 1-800-554-6723.

CHAIN BRAKE

WARNING: The effectiveness of a chain brake in reducing operator injuries has not yet been fully determined. We cannot represent that a chain brake is an effective safety device to prevent or reduce the haz- ard of injuries resulting from kickback. DO NOT ASSUME THAT THE CHAIN BRAKE WILL PROTECT YOU IN THE EVENT OF A KICKBACK. Instead, use the saw properly and carefully to avoid kickback. Reduced-- Kickback bars and Low--Kickback chains re-

9

duce the hazard of kickback and are recom- mended. If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. Repairs on a chain brake should be made by an Authorized POULAN PRO Service Dealer. Take your unit to the place of purchase if purchased from a Servicing Dealer, or to the nearest Au- thorized Master Service Dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

SThe inertia activated chain brake is activated if the front hand guard is pushed forward, either manually or by centrifugal force.

SIf the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Braking function control

The chain brake must be checked several times daily. Place the saw on firm ground. Hold the handles with both hands and apply full throttle. Activate the chain brake by turn- ing your left wrist against the hand guard without releasing the grip around the front handle. The chain should stop immediately.

Inertia activating function control

CAUTION: When performing the following procedure, the engine must be turned off.

Disengaged

Engaged

The chain brake must be checked several times daily. Hold the chain saw approxi- mately 14” (35 cm) above a stump or other firm object. Release your grip on the front handle and let the saw, by its own weight, rotate around the rear handle. When the tip of the bar hits the stump, the brake should activate.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 295 Operate Your SAW Safely Plan AheadMaintain Your SAW in Good Working Order UnitHandle Fuel with Caution KickbackAgainst kickback Maintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InStand with your weight evenly balanced on both feet Kickback Safety FeaturesFor gasoline powered chain saws as set by Ansi B175.1 Chain Brake CKA AngleAttaching the BAR & Chain Computed kickback angle CKA TableAdjusting the tension Chain TensionChecking the tension BAR and Chain Lubrication Fueling EngineImportant points to remember For cold engine or warm engine after run- ning out of fuelBraking function control Chain BrakeInertia activating function control For a warm engineTree Felling Techniques Important PointsFelling Large Trees Increase the possibility of kickbackCutting a Fallen Tree Bucking Using a LOG or Support StandImportant points Types of Cutting Used for BuckingLimbing and Pruning Important Points Cleaning the air filterLimbing PruningCarburetor Adjustments BAR MaintenanceChain Sharpening Ignition TimingLigations The U. S. Environmental Your Warranty Rights and OBEater service centers. call 1--800--554--6723MAINTENANCE, RE

295 specifications

The Electrolux 295 is an innovative and efficient appliance designed to elevate your laundry experience. It combines modern technology with user-friendly features, making it a favorite among households that value both performance and convenience.

One of the standout characteristics of the Electrolux 295 is its large capacity. With ample space, it can easily handle large loads of laundry, which is ideal for families or those who prefer to do their laundry less frequently. This capacity not only saves time but also energy, as fewer loads mean reduced energy consumption over the long term.

The appliance is equipped with advanced cleaning technologies that ensure effective stain removal and fabric care. Its proprietary UltraCare system gently washes clothes while maintaining their quality. This system uses lower wash temperatures paired with specialized detergents to deliver outstanding cleaning results without compromising the integrity of delicate fabrics.

The Electrolux 295 also features a range of wash cycles that cater to various fabric types and soil levels, providing tailored care for every load. Options include quick wash for lightly soiled clothes, heavy-duty for robust cleaning, and eco-friendly cycles that minimize water and energy use. This versatility ensures that users can find the optimum setting for their particular needs.

In terms of energy efficiency, the Electrolux 295 has been designed to meet modern standards. It boasts an impressive energy star rating, indicating that it operates with minimal energy consumption. This not only helps the environment but also reduces utility bills, making it a cost-effective choice over time.

The intuitive control panel is another feature that sets the Electrolux 295 apart. With a straightforward interface, users can easily select their desired settings without confusion. Additionally, the appliance is designed for quiet operation, which means that it can run in the background without disturbing daily activities.

Furthermore, the Electrolux 295 is built with durability in mind, featuring high-quality materials and robust construction to ensure a long lifespan. The combination of advanced technology, efficiency, and user-friendly operation makes the Electrolux 295 a standout choice for modern laundry needs. Whether you’re dealing with tough stains or simply need a reliable washer for daily use, the Electrolux 295 proves to be a versatile and reliable option in today’s market.
Top Page Image Contents