Electrolux AG15538A manual Tractor

Page 18

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rub- ber.

•Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac- tor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Trailing

Mandrel

Assembly

Edge Up

Blade

Flat

 

Washer

 

Lock

 

Washer

 

Blade Bolt

Star

Center Hole

 

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

 

Center Hole

5/8" Bolt

Blade

or Pin

 

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model NO. AG15538A Table of Contents WarrantySafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesUnassembled Parts To Remove Tractor from Carton Tools Required for AssemblyHOW to SET UP Your Tractor Before Removing Tractor from SkidCheck Battery Check for Proper Position of ALL Belts ChecklistCheck Tire Pressure Check Deck LevelnessOperation Light Switch Position Turns the headlights on and off Know Your TractorHOW to USE Your Tractor Before Starting the Engine To Start Engine ADD GasolineMowing Tips Maintenance General Recommendations Lubrication ChartBefore Each USE Tractor Transaxle Cooling Clean AIR ScreenEngine BeltsMuffler CleaningAIR Filter Spark PlugsService and Adjustments To Install MowerTo Remove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt To Remove Wheel for RepairsTo Attach Jumper Cables Replacing BatteryTo Start Engine with a Weak BAT- Tery To Remove CABLES, Reverse OrderTo Adjust Carburetor Fuel System BatteryOther Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

AG15538A specifications

The Electrolux AG15538A is a vacuum cleaner designed to cater to the needs of modern households, combining advanced technology with user-friendly features to provide efficient cleaning. This model is part of Electrolux's extensive range known for its reliability, efficiency, and innovative design.

One of the standout features of the AG15538A is its powerful motor, delivering impressive suction capabilities. This ensures that it can easily pick up dirt, dust, and debris from various surfaces, including carpets, hardwood floors, and tiles. The vacuum's suction power is complemented by its efficient filtration system, which captures allergens and fine dust particles, making the home environment healthier and more comfortable.

The vacuum cleaner incorporates a multi-cyclonic technology, which helps to separate dirt and air, ensuring that suction power remains consistent even as the dust container fills up. This feature not only enhances cleaning efficiency but also reduces maintenance, as the filters require less frequent replacement. Additionally, the bagless design allows for easy disposal of collected dirt, reducing the hassle of bag replacements and contributing to convenience.

The AG15538A is designed for ease of use, featuring an ergonomic handle and lightweight construction that make it easy to maneuver around furniture and reach high places. Its adjustable suction settings allow users to customize the cleaning experience based on the type of surface being cleaned, ensuring optimal performance on all floor types.

Another notable characteristic of this vacuum is its quiet operating system. Despite its powerful suction, the AG15538A operates at a much lower noise level compared to traditional vacuum cleaners, allowing for peaceful cleaning without disturbing other household members.

In terms of storage, the vacuum is compact, making it easy to stow away when not in use. Its longer cord also adds to the convenience, allowing users to clean larger areas without frequently changing outlets.

Overall, the Electrolux AG15538A combines modern technology with thoughtful design, making it a reliable choice for households looking for a powerful, efficient, and easy-to-use vacuum cleaner. Its advanced features reflect Electrolux’s commitment to creating innovative home appliances that enhance everyday living.
Top Page Image Contents