Craftsman 987.799601 manual OFF-SEASON Storage

Page 32

STORAGE

OFF-SEASON STORAGE

DANGER

To Prevent Personal injuryor Property Damage:

*Never perform maintenance while engine is runningor when spark plug wire is connectedto spark plug, exceptwhere specifically instructedto do so.

,, Never store machine with fuel in the fuel tank inside a building where fumes may reach an open flame or spark, or where ignitionsourcesare present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc_

NOTE: A yearly check-up by your local Sears Service Center is a good way to ensure that your machine will provide maximum performance for the next season.

1.Review the "Customer Responsibilities and Storage" safety rules in the Safety Section of this Manual

2.To prevent engine damage (if the machine is not used for more than 30 days) follow the steps below:

a.It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose or tank during storage, Also, experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage Acidic gas can damage the fuel system of an engine while in storage.,

b.To remove gasoline, run the engine until the tank is empty and the engine stops.

c.If you do net want to remove gasoline, a fuel stabilizer (such as Craftsman Fuel Stabilizer No 335500) may be added to any gasoline left in the tank to minimize gum deposits and acids If the tank is almost empty, mix the stabilizer with fresh gasoline in a separate container and add some to the tank. ALWAYS FOLLOW INSTRUCTIONS ON THE STABILIZER CONTAINER, THEN, RUN THE ENGINE AT LEAST 10 MINUTES AFTER THE STABILIZER IS ADDED TO ALLOW MIXTURE TO REACH CARBURETOR. STORE THE MACHINE IN A SAFE PLACE SEE DANGER ABOVE

d.Change the oil if it has not been changed in the last three months, See Page 28

e.Lubricate the piston/cylinder area,, First, remove

the spark plug, Then, squirt approximately '1/2 ounce of clean engine oil into the spark plug hole_ Cover the spark plug hole with a rag to absorb oil

spray and then rotate the engine by pulling the starter rope two or three times. Finalty, re-install

the spark plug.

f.Clean the engine by removing any dirt, chaff or other debris from its exterior.

3.Thoroughly clean the machine, collection bag, hose, and blower deflector.

4.Check that all hardware is in place and securely fastened. Refer to the Parts List in this Manual for

replacement hardwarer

5.Inspect all visible moving parts for damage,

breakage, and wear_ Repair or replace as needed (refer to Parts List).

6.Touch up paint on all chipped or scratched surfaces to prevent rust from forming.

7.If possible, store machine indoors (see DANGER statement on this page) Cover machine for protection from dust and dirt. Use a covering (not plastic) that does not retain moisture, Be sure the engine and muffler are cool before covering the machine,

32

Image 32
Contents SEA/ S Preparation Safety RulesTraining Operation Maintenance and Storage Safety DecalsLimited ONE Year Warranty Maintenance AgreementProduct Specifications Customer ResponsibilitiesTable of Contents Vacuum Hose Engine AccessoriesAttachments Assembly Unfold the Handlebars see FigureCheck ALL Nuts and Bolts for TightnessAssembly Assembly ConfigurationsAssembly for WALK-BEHIND Vacuuming or Using the Chipper Remove or Install Shredder ScreenTo Install Shredder Screen To Remove Shredder ScreenInstall Vacuum Inlet CAP Install Collection BAGAdjust the Vacuum Inlet Height Assembly for Blower Operation Adjust HandlebarsInstalled Adjust the Vacuum Inlet HeightRemove the Shredder Screen Install Blower DeflectorInstall Vacuum Inlet CAP Assembly for Optional Vacuum Hose Operation Remove Blower Deflector if InstalledMove Handlebars to Vacuuming Position Handlebars in VacuumInstall Collection BAG CAUTiORInstall Baffle Plate Install HoseBaffle Plate Removal Remove Vacuum Inlet CAPOperation Know Your CHIPPERiVACDahger Before Starting EngineStep t ADD OIL to Engine ADD Gasoline to the Fuel TankPRE-STARTING Procedures Safetyinterlock SystemOperation To Add GasolineGeneral Operation Starting the Engine Stopping the EngineVacuuming Operation Chipping OperationVacuuming and Chipping Guide Materials to AvoidWalk-Behind Vacuuming Tips and Hints WALK-BEHIND Vacuuming OperationOperation Operation Tips for Using the Vacuum HoseVacuum Hose Operation Blower Operation Blower operationChipper Flap is Worn or Missing Tips for Using the ChipperChipper Operation Clearing Jams and Clogs Stop the Engine Immediately and wait for allCheck and Change Engine OIL MaintenancescheduleImportant Service Message If SO Equipped Service the AIR FilterCustomer Responsibilities Carburetor and Ignition System Information Check Bolts and Nuts for TightnessLubrication Check The Spark PlugService AdjustmentsWARNIH8 DanserService and Adjustments Torque SpecificationsBoltSize Locationof BoltsStorage OFF-SEASON StorageTroubleshooting Points ProblemCorrection Possible CausePossiblecause Inletcaporhose Mustbeinstalled DecalsRotatingcumng Blade Do Nottouch Muffleror AdjacentareasCRAFTSMAI!5 HP CHIPPER/VACMODELNUMBER987.799601 12iCRAFTSMAN5 HP CHIPPER/VACMODELNUMBER987.799601 Part Description QTYPart Description QTYNumbershere CRAFTSMAN4-CYCLE EngineMODELand SERIALIZe CRAFTSMAN4-CYCLE Enginemodel HO Part Name TefRepairparts Carburetorno FigRewindstarterno Fig Hosekit noPage Page Page For Repair Service Call this Toll Free Number Part Number Part Description

987.799601, 79960 specifications

The Craftsman 79960,987.799601 is a power tool that embodies the philosophy of innovation combined with user-friendly design. Created for both amateur and professional users, this tool stands out in the marketplace due to its unique blend of versatility, power, and comfort.

At the heart of the Craftsman 79960 is a robust motor that delivers exceptional performance across various tasks. With a peak horsepower that allows for greater efficiency and productivity, users can tackle everything from woodworking and metalworking to home repairs with ease. Whether you are making precision cuts or performing heavy-duty drilling, this tool is equipped to handle it all.

One of the main features of the Craftsman 79960 is its lightweight and ergonomic design. The handle is thoughtfully crafted to provide a comfortable grip, reducing user fatigue during extended use. This is especially beneficial for professionals who require hours of continuous operation. Furthermore, its balanced weight distribution ensures optimal control and stability, contributing to superior performance.

The Craftsman 79960 also integrates advanced technology that sets it apart from its competitors. The inclusion of variable speed settings allows users to adjust the tool’s performance based on the task at hand. This feature is particularly useful for projects that require different levels of power and precision, making it suitable for delicate tasks as well as more robust applications.

In addition to its functionality, safety is a key consideration in its design. The Craftsman 79960 is equipped with an array of safety features, including an automatic shut-off function that activates in the event of overheating or abnormal operation. This offers peace of mind for users, allowing them to focus on their work without worrying about potential mishaps.

Durability is another highlight of the Craftsman 79960. Constructed with high-quality materials, this tool is built to withstand the rigors of daily use, ensuring longevity and reliability. Coupled with Craftsman's renowned warranty and support, users can rest assured that they are investing in a product designed to endure.

In summary, the Craftsman 79960,987.799601 is a powerful, versatile, and extremely user-friendly tool that caters to various needs. Its combination of powerful performance, advanced technology, ergonomic design, and safety features make it an exceptional choice for anyone looking to enhance their tool collection. Whether you're a hobbyist or a professional tradesperson, this tool is sure to meet and exceed your expectations.