Craftsman 79960 manual Service and Adjustments, Torque Specifications, BoltSize, Locationof Bolts

Page 31

SERVICE AND ADJUSTMENTS

7, The chipper cutting blade (A in Figure 33) is mounted on the upper side of the flywheel assembly (B). AVOID CONTACT WITH THE BLADE AS IT tS EXTREMELY SHARP! To remove the blade, first remove the flywheel assembly as described below:

a.Rotate the flywheel assembly until the cutout (C) in the flywheel assembly is located below the chipper chute, To prevent the flywheel assembly from turning, place a 1/2" or thicker wood dowel down the chipper chute through the cutout. See Figure 33.

b, Using a box end 9/16" wrench, remove the

bolt (D) and concave washer (E) Carefully slide the assembly off the crankshaft Do not lose the key (F), or any shims (G), NOTE: Shims (if used) may be inside bore of flywheel assembly, See Figure 33

8.With a 3/16" hex key (Allen) wrench and 1/2" box wrench, remove the two Iocknuts (I) and screws (H) that

secure the blade to flywheel assembly., If necessary,

first clean out the socket holes in the screw heads with a sharp nail or awl, See Figure 33

9.Before installing a new or resharpened blade, thoroughly clean the area where the blade seats on the flywheel assembly (also clean the old blade, if it is being reused).

10.Position the blade on the upper side of the flywheel assembly, with the sharp edge of the blade on top, Install two new screws down through the blade and add new focknuts_ Use only factory-suppliedhardware. Do not use substitutes or equipment failure or personal injury could result. Tighten securely (torque to 240 lbs-in or 20 Ibs-ft)

11.Place key (F) in the engine crankshaft and re-install any shims (G). Align the keyway in the bore with the key on the crankshaft and slide the flywheel assembly into place

12.Place the concave washer (E [dished-in side of washer faces flywheel assembly]) on the mounting bolt

(D) and install the bolt in the crankshaft. Tighten securely (torque to 204 Ibs-in) Remove the wood dowel from the chipper chute

13.Replace the engine in the chassis, with the spark plug side facing the front (toward Inlet Cap)

14. Install the short safety interlock wire terminal and

the lockwasher on one of the mounting bolts and install it at the rear of the machine above the left side of the

blower opening. Connect the long interlock wire to the terminal above the muffler. Replace the other two mounting bolts and tighten all three bolts to 60-65 Ibs-in.

DO NOT OVERTIGHTEN BOLTS OR DAMAGE COULD RESULT TO HOUSING

15.install shredder screen in housing, insert screen rods, and secure with hair pin clips.

16.Replace the collection bag or blower deflector and reposition the handlebars in the correct operating position for vacuuming or blower operation°

Figure 33t Chipper cutting blade removal/replacement,

 

TORQUE

SPECIFICATIONS

BoltSize

Torque(Ibs-in)

 

Locationof Bolt(s)

5/16"-t4

60-65]Bs-in

1

Enginemountingplateto housing

 

40-55Ibs-in

2

Handlepivot bracket

 

40-55tbs-in

3

Upperhousingto lowerhousing

5/16"-24

240tbs-in

1. Chipperknifeto fanassembly.

3/8"-t6

180lbs-in

1

Wheelballs

 

 

2.

Handlebarsto pivotbrackets.

3/8"-16

276lbs-in

1.

Enginemountingplateto engine

3/8"-24

204lbs-in

1

Fanassemblyto engine

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents SEA/ S Training Safety RulesPreparation Operation Safety Decals Maintenance and StorageCustomer Responsibilities Limited ONE Year WarrantyMaintenance Agreement Product SpecificationsTable of Contents Attachments Engine AccessoriesVacuum Hose Tightness AssemblyUnfold the Handlebars see Figure Check ALL Nuts and Bolts forAssembly Configurations AssemblyTo Remove Shredder Screen Assembly for WALK-BEHIND Vacuuming or Using the ChipperRemove or Install Shredder Screen To Install Shredder ScreenAdjust the Vacuum Inlet Height Install Collection BAGInstall Vacuum Inlet CAP Adjust the Vacuum Inlet Height Assembly for Blower OperationAdjust Handlebars InstalledInstall Vacuum Inlet CAP Install Blower DeflectorRemove the Shredder Screen Handlebars in Vacuum Assembly for Optional Vacuum Hose OperationRemove Blower Deflector if Installed Move Handlebars to Vacuuming PositionCAUTiOR Install Collection BAGRemove Vacuum Inlet CAP Install Baffle PlateInstall Hose Baffle Plate RemovalKnow Your CHIPPERiVAC OperationADD Gasoline to the Fuel Tank DahgerBefore Starting Engine Step t ADD OIL to EngineTo Add Gasoline PRE-STARTING ProceduresSafetyinterlock System OperationStarting the Engine Stopping the Engine General OperationMaterials to Avoid Vacuuming OperationChipping Operation Vacuuming and Chipping GuideOperation WALK-BEHIND Vacuuming OperationWalk-Behind Vacuuming Tips and Hints Vacuum Hose Operation Tips for Using the Vacuum HoseOperation Blower operation Blower OperationChipper Operation Tips for Using the ChipperChipper Flap is Worn or Missing Stop the Engine Immediately and wait for all Clearing Jams and ClogsImportant Service Message MaintenancescheduleCheck and Change Engine OIL Customer Responsibilities Service the AIR FilterIf SO Equipped Check The Spark Plug Carburetor and Ignition System InformationCheck Bolts and Nuts for Tightness LubricationDanser ServiceAdjustments WARNIH8Locationof Bolts Service and AdjustmentsTorque Specifications BoltSizeOFF-SEASON Storage StoragePossible Cause Troubleshooting PointsProblem CorrectionPossiblecause Do Nottouch Muffleror Adjacentareas Inletcaporhose MustbeinstalledDecals Rotatingcumng Blade12i CRAFTSMAI!5 HP CHIPPER/VACMODELNUMBER987.799601Description QTY CRAFTSMAN5 HP CHIPPER/VACMODELNUMBER987.799601Part Description QTY PartMODELand SERIALIZe CRAFTSMAN4-CYCLE EngineNumbershere Part Name Tef CRAFTSMAN4-CYCLE Enginemodel HOHosekit no RepairpartsCarburetorno Fig Rewindstarterno FigPage Page Page Part Number Part Description For Repair Service Call this Toll Free Number

987.799601, 79960 specifications

The Craftsman 79960,987.799601 is a power tool that embodies the philosophy of innovation combined with user-friendly design. Created for both amateur and professional users, this tool stands out in the marketplace due to its unique blend of versatility, power, and comfort.

At the heart of the Craftsman 79960 is a robust motor that delivers exceptional performance across various tasks. With a peak horsepower that allows for greater efficiency and productivity, users can tackle everything from woodworking and metalworking to home repairs with ease. Whether you are making precision cuts or performing heavy-duty drilling, this tool is equipped to handle it all.

One of the main features of the Craftsman 79960 is its lightweight and ergonomic design. The handle is thoughtfully crafted to provide a comfortable grip, reducing user fatigue during extended use. This is especially beneficial for professionals who require hours of continuous operation. Furthermore, its balanced weight distribution ensures optimal control and stability, contributing to superior performance.

The Craftsman 79960 also integrates advanced technology that sets it apart from its competitors. The inclusion of variable speed settings allows users to adjust the tool’s performance based on the task at hand. This feature is particularly useful for projects that require different levels of power and precision, making it suitable for delicate tasks as well as more robust applications.

In addition to its functionality, safety is a key consideration in its design. The Craftsman 79960 is equipped with an array of safety features, including an automatic shut-off function that activates in the event of overheating or abnormal operation. This offers peace of mind for users, allowing them to focus on their work without worrying about potential mishaps.

Durability is another highlight of the Craftsman 79960. Constructed with high-quality materials, this tool is built to withstand the rigors of daily use, ensuring longevity and reliability. Coupled with Craftsman's renowned warranty and support, users can rest assured that they are investing in a product designed to endure.

In summary, the Craftsman 79960,987.799601 is a powerful, versatile, and extremely user-friendly tool that caters to various needs. Its combination of powerful performance, advanced technology, ergonomic design, and safety features make it an exceptional choice for anyone looking to enhance their tool collection. Whether you're a hobbyist or a professional tradesperson, this tool is sure to meet and exceed your expectations.
Top Page Image Contents