Craftsman 917.27075 SIDE-TO-SIDE Adjustment, BottomEdge, Nut F, FRONT-TO-BACK Adjustment

Page 22

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCTSPECIFICATIONS"section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the same or

within 1/4" of each other.

°If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side. NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

BottomEdge

_

Bottom Edge

of Mower to_--7_/,_-_/__of

Mower to

Ground XI-I__

 

_.ound

A-T_"-_

Ground Une_

_--A

Suspension

Arm

•Before making any necessary adjust- ments, check that both front links are

equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links.

Tighten nut "E" on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

Mandrel

Both Front Links Should be Equal in Length

Nut "F" _

Nut "E"

Lift Unk Adjustmen_ Nut

Trunnion /

 

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to-side. If the following front-to-backadjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

Front Links

TO REPLACE MOWER BLADE DRIVE BELT (See Illustration Next Page) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL-

•Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual).

•Work belt off both mandrel pulleys and

idler pulleys.

22 • Pull belt away from mower.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents RHFTSMRNo Warranty Limited 90 DAY Warranty on BatterySlope Operation General OperationBe sure the area is clear of other people Do notService Grass can hide obstaclesAPI-SF/SG/SH System Battery AMP/HR MIN. CCAFety is Involved BelowSeat Steering WheelKeys Video Cassette Slope Sheet To Remove Tractor from Carton HOW to SET UP Your TractorBefore Removing Tractor from Skid Install Seat Install Mulcher PlateTo Drive Tractor OFF Skid Check Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsBattery Reverse Forward Fast Slow Know Your Tractor HOW to USE Your Tractor To Operate Mower To Adjust Mower Cutting HeightTo Adjust Gauge Wheels LowADD Gasoline Towing Carts and Other AttachmentsBefore Starting the Engine To TransportWarm Weather Starting 50 F and Above To Start EngineCold Weather Starting 50 F and below Mowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Battery TractorClean AIR INTAKF-JCOOLING Areas EngineMuffler Engine OIL FilterAIR Filter Spark PlugsTractor CleaningTo Install Mower To Remove MowerBottomEdge SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment Nut FTransaxle Gear Shift Lever Adjustment Belt InstallationTo Adjust Brake To Replace Motion Drive BeltTo Remove Wheel for Repairs To Start Engine with a Weak BatteryTo Adjust Steering Wheel Alignment To Attach Jumper CablesTo Replace Headlight Bulb To Remove Hood and Grill AssemblyReplacing Batiery Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control EngineEngine OIL OtherFuel System CylindersTroubleshooting Chart Problem Cause CorrectionExcessive vibration Wom, bent or loose blade Check all wiring Check/replace solenoid or starterEngine clicks but Loose or damaged Check oil level/change oilTroubleshooting Problem Chart CauseTractor - Model Number Schematic Tractor --MODEL Number ElectricalTractor - Model Number Electrical KEY Part DescriptionTractor - Model Number 917.270750 Chassis and Enclosures Tractor - Model Number 917.270750 Chassis and Enclosures Tractor - Model Number Ground Drive X .1845/1865 Tractor - Model Number 917.270750 Steering Assembly Tractor - Model Number Steering Assembly KEY Part NO. noTractor - Model Number Engine124028X Tractor - Model Number Seat Assembly 71110616Tractor - Model Number Decals Wheels TiresTractor - Model Number Lift Assembly Ring #5133-62 Tractor - Model Number Mower Deck STD533710 O71B 778345 1o3526o 211 2093 SO 2o Sealing Washer 694000 Page Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Direction on slopesMY-HOMEsMAnytime, day or night 174323

917.27075 specifications

The Craftsman 917.27075 is a versatile and reliable lawn tractor, designed specifically for homeowners seeking a dependable solution for lawn care. This model exemplifies the blend of power and precision that has made Craftsman a leading name in outdoor equipment.

One of the standout features of the Craftsman 917.27075 is its robust 24 HP Kohler engine, providing ample power to tackle a variety of tasks, from mowing to towing. The engine is designed for efficient performance, ensuring a smooth operation, while the hydrostatic transmission allows for seamless acceleration and deceleration. This feature enhances maneuverability, making it easier to navigate tight corners and tricky landscapes.

The mowing deck on the Craftsman 917.27075 measures 46 inches, which offers a wide cutting path to cover more ground in less time. The deck is adjustable, allowing users to choose from different cutting heights, which is essential for achieving the perfect lawn finish. With its mulching capability, this tractor can easily return nutrients to the soil, promoting healthier grass growth.

Comfort is another critical aspect of the 917.27075 design. The lawn tractor comes equipped with an ergonomic seat, padded for support during extended mowing sessions. The steering wheel is positioned for ease of use, making control intuitive. Additionally, the tractor features easy-to-reach controls, further enhancing user comfort and operational efficiency.

One of the advanced technologies integrated into this model is the Smart Engage blade system, which provides a reliable blade engagement and can be activated with minimal effort. This system contributes to a more pleasant mowing experience, especially for those who may struggle with more traditional engagement mechanisms.

The Craftsman 917.27075 also includes a rugged chassis, built to withstand the rigors of regular use. The front and rear tires are designed for excellent traction, ensuring stability on uneven terrain. Its durable body construction means it can handle everyday wear and tear, making it a long-term investment for homeowners.

In summary, the Craftsman 917.27075 lawn tractor combines power, comfort, and technology, making it an ideal choice for efficient lawn care. Its strong engine, intuitive features, and robust build provide a reliable solution for maintaining a beautiful lawn with minimal effort. Whether you are mowing, bagging, or mulching, this lawn tractor reaffirms Craftsman's legacy of quality and performance in outdoor power equipment.
Top Page Image Contents