Craftsman 917.28035 To Replace Mower Blade Drive Belt, Belt Removal, Belt Installation

Page 24

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade drive belt may be replaced without tools. Park the tractor on level sur-

face. Engage parking brake.

BELT REMOVAL-

1. Remove mower. (See "TO REMOVE MOWER" in this section of manual.)

2.Work belt off mandrel pulley and idler pulleys.

3.Pull belt away from mower.

BELT INSTALLATION-

1.Work belt around mandrel pulley and idler pulleys

2.Make sure belt is in all pulley grooves and inside all belt guides.

3.Install mower (See "To Install Mower" in this section of this manual).

Mandrel Pulle'

Idler

fs

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a

level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing

freewheel control in "transmission disen-

gaged" position. Pull freewheel control out and into the slot and release so it is

held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a Sears or other qualified service center.

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is

a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL-

1.Remove mower (See "TO REMOVE

MOWER" in this section of manual). NOTE: Observe entire motion drive belt

and position of all belt guides and keepers.

2.Remove belt from stationary idler (A) and clutching idler (B).

3.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D).

4.Remove belt downward from engine pulley (E).

5.Slide belt toward rear of tractor, off the steering plate (F) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steering plate (F) and above clutch brake pedal shaft (G).

2.Pull belt toward front of tractor and roll belt onto engine pulley (E).

3.Pull belt toward rear of tractor. Care- fully work belt down around transaxle input pulley (D). Be sure belt is inside the belt keeper.

4.Install belt through stationary idler (A) and clutching idler (B).

5.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

6.Install mower (See "TO INSTALL MOWER" in this section of manual).

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents LAW Tracto Craftsman Full Warranty TWO Years on Riding Equipment General Operation Service Safe Handling of GasolineGeneral SERVlCEProduct Specifications Repair Protection411111 Tools Required for Assembly To Check BatteryBefore Removing Tractor from Skid To Remove Tractor from Carton Unpack CartonTo Adjust Seat To Assembly BaggerPaddle Check Tire PressureCheck for Proper Position of ALL Belts @@@@ Know Your Tractor Reverse Operation System ROSHOW to USE Your Tractor StoppingEngine To SET Parking BrakeTo Operate Mower To Stop Mower BladeTo Transport Towing Carts and Other ATTACH- MentsBefore Starting the Engine To Start EngineCheck Engine OIL Level To Operate on HillsMowing Tips Mulching Mowing TipsTo Dump Bagger Maintenance Lubrication ChartSchedule Tires Battery EngineTo Change Engine OIL BeltsEngine Cooling System MufflerTo Install Mower To Remove MowerAttach Mower Side Suspension Visual SIDE-TO-SIDE Adjustment FRONT-TO-BACK Adjustm ENTPrecision SIDE-TO-SIDE Adjustment To Level MowerBelt Installation To Replace Mower Blade Drive BeltBelt Removal To Replace Motion Drive BeltTransaxle Gear Shift Lever NEU= Tral Adjustment To Adjust Steering WheelTo Remove Wheel AlignmentReplacing Battery Interlocks and RelaysFuel System Engine OILTroubleshooting Chart Problem Cause CorrectionProblem Cause CorrectionProblem Level mower deckNeed More HELP? Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXEspecificaciones del Producto Funcionamiento General III, Ninos IV. RemolqueOperaciones DE Servicio Generales Page Especificacionesdel Producto LA REPARACI6NResponsabilidades DEL Cliente 411111 Herramientas Necesarias Para EL Montaje Para Remover EL Tractor DE LARemuevay desechesedelcinta Para Montar EL ContenedorPara Ajustar EL Brazo Completo CON PaletaRevision DE LA Presion DE LAS Llantas DE Todas LAS Correas@@@@@ Familiaricese CON SU Tractor SU TractorPalanca DEL Levantamiento DEL Palanca DEL Freno DEComo Usar SU Tractor ParadaFuncionamiento Atras Para Operar EN Cerros Antes DE Hacer Arrancar ELMotor Consejos Para Segar Y Acolchar Consejospara SegarAntes DE Cada USO MantenimientoTractor LlantasVeri Fiez Sistema Funci Onam Iento AT RA,S ROS Cuidado DE LA CuchillaCorreasv Motor LubricacionPara CAM Biar Elaceite DEL Motor Filtro DEL AireLimpiezadela Rejilladeaire LimpiezaSilenciador Filtro DE Combustible EN LineaCesped Vicio O DE Hacer AjustesPara Desmontar LA Cortadora DE Instale LA SegadoraFije LOS Brazos DE Suspension Fije LA Pieza DE Union AnteriorRegulacionvisualdeladoa Lado Ajuste DE Delante a ATR,SRegulacion DE LA Precision DE Lado Para Cambiar LA Cuchilla DEL Regulaciondela Palancade VELOCI= Para Remover LAS RuedasPara Ajustar EL Alineamiento DEL Volante DE Direccion CONVERGENCIA/INCLINACION DE LAS Ruedas DelanterasReemplazarla Bateria MotorPara Cambiar EL Fusible Tractor OtrosSistema DE Combustible Aceite DEL MotorIDENTIFICACI6N DE Problemas CausaIdentificaciondeproblemas El corteLas luz ces de Lanteras no funcio Page Operacion Segura Cuesta Abajo Y no Atraviese EL Cerro15GRADOS MAX Your Home SR/AP
Top Page Image Contents