Craftsman 917.274953 manual To Level Mower Housing, SIDE-TO-SIDE Adjustment

Page 21

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

9.Connect anti-swaybar to chassis bracket under left footrest and retain

with double loop retainer spring.

10.If equipped, turn height adjustment knob clockwise to remove slack from

mower suspension.

11.Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure

tires are properly inflated (See =PROD-

UCT SPECIFICATIONS" section of this

manual). If tires are over or undednflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•Measure height from bottom edge of

mower to ground level at front corners of mower. Distance =A" on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

Bottom Edge of

Bottom Edge of

Mower to Ground

Mower to Ground

\

/

Check adjustment on right side of tractor. Measure distance =P directly in front of and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front plats links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower housing, loosen nut =G"on both front links an equal number of turns.

•When distance =P is 1/8" to 1/2" lower

at front than rear, tighten nut =H" against trunnion on both front links.

•To raise front of mower housing, loosen nut =H" from trunnion on both front links.

Tighten nut "G" on both front links an equal number of turns.

•When distance =P is 1/8" to 1/2" lower

at front than rear, tighten nut "H" against trunnion on both front links,

NOTE: Each fullturn of nut =G" will

change distance =P by approximately 3/8".

•Recheck side-to-side adjustment.

\

Mandrel

BOTH FRONT PLATE LINKS MUST BE

EQUAL IN LENGTH

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to- side. If the following front-to-backadjustment is necessary, be sure to adjust

both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Nut

Front Plate Trunnion

Assembly

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents SEARS, Roebuckand CO., Hoffman ESTATES, IL60179 U.S.A IcrrftsmrniLimited Warranty on Craftsman Riding Equipment Safety is Involved II. Slope OperationGeneral Operation IV. Service Do notIII. Children Page Repair Agreement Product SpecificationsAPI-SF-SJ RC12YCCheck Battery To Remove Tractor fromUnpack Carton Knob Adjust SeatCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemKeep Area Clear Slope Hazards Knowyour Tractor Stopping Mower Blades HOW to USE Your Tractor to SET Parking BrakeTo Operate Mower To Adjust Gauge WheelsTo Stop Mower Blades To Operate on HillsTowing Carts and Other Attach Ments To TransportBefore Starting the Engine Check Engine OIL Level ADD GasolineMowing Tips Lubrication Chart General RecommendationsBefore Each USE Tires Brake OperationOperator Presence System Blade CareEngine Muffler Spark PlugsIN-LINE Fuel Filter Tractor To Remove Mower To Install MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentBoth Front Plate Links Must be Equal in Length To Replacemowerdrivebelt Mowerdrivebeltremoval Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt To Adjust BrakeTo Adjust TOE-IN To Replace Motion Drive BeltFront Wheel Camber Front Wheel Replacing BatteryRear Wheel To Start Engine with a WeakInterlocks and Relays To Replace Headlight BulbTo Replace Fuse EngineTo Adjust Carburetor To Adjust Choke ControlFinal Setting Acceleration TestEngine Fuel System =TO Clean BAI-IERYANDTERMIEngine OIL CylindersTroubleshooting Chart Cause CorrectionStart Engine Troubleshootingchart ProblemCause Correction ProblemcausePage TRACTOR-- Model Number SchematicElectrical Tractor - Model NumberKEY Part Description Tractor -- Model Number ElectricalTractor -- Model Number 917.274953 Chassisand Enclosures Tractor - Model Number 917.274953 Chassis and Enclosures Tractor - Model Number Ground Drive KEY Part Description NO. no Tractor - Model Number Ground DriveTractor - Model Number 917.274953 Steering Assembly Tractor -- Model Number 917.274953 Steering Assembly 40I Spark Arrester KIT Tractor -- Model NumberTractor -- Model Number 917.274953 Seatassembly Tractor --MODEL Number DecalsWHEELS&TIRES Lift Assembly Tractor -- Model Number Mower Deck Tractor - Model Number Mowerdeck Tractor -- Model Number Transaxle Description Part Transaxle KEY Part NO. noCylinder HEAD, Valve and Breather Crankcas HEADNALVF./BREATHER KEY Part Description Tractor -- Model Number14--1 KEY Part Description TractorNot Illustrated AIR INTAKE/FILTRATIONStarting System J KEY Part NO. NO.DESCRIPTION Starting System KEY Part NO. NO.DESCRIPTIONCrankshaft J Exhaust Fuel System Not Illustrated KEY Part NO. no Exhaust KEY Part NO. NO.DESCRIPTIONPage Suggested Guide for Sighting Slopes for Safe Operation AuCanadapourserviceenfranab

917.274953 specifications

The Craftsman 917.274953 is a powerful and versatile lawn mower that has gained popularity among homeowners and landscaping enthusiasts. Known for its reliability and performance, this mower is designed to handle a variety of lawn sizes and types, making it an excellent choice for maintaining a beautifully manicured outdoor space.

One of the standout features of the Craftsman 917.274953 is its robust engine. Equipped with a 42-inch cutting deck, the mower is powered by a reliable Briggs & Stratton engine. This engine delivers sufficient power to tackle thick grass and uneven terrain with ease. The self-propelled drive system allows users to effortlessly maneuver the mower across their lawns, reducing fatigue and making the mowing process more efficient.

Another notable characteristic of this mower is its adjustable cutting height. With multiple height settings, users can easily customize the length of their grass to achieve their desired lawn appearance. This flexibility is particularly useful during different growing seasons, allowing users to adapt to changing grass conditions.

In terms of technology, the Craftsman 917.274953 incorporates innovative features that enhance its usability. The mower is designed with a rear bagging system, which efficiently collects clippings, leaving a clean finish after mowing. For those who prefer mulching, the mower also includes a mulching option that allows grass clippings to be finely chopped and returned to the soil, providing natural nutrients.

Additionally, the Craftsman mower boasts a durable construction, featuring a robust steel deck that ensures longevity and resistance to wear and tear. This quality construction not only extends the mower's lifespan but also enhances its performance in various weather conditions.

The ergonomic design of the mower offers user comfort, with an adjustable handle that accommodates different heights. This attention to comfort minimizes strain during extended use, making it suitable for homeowners with larger properties.

Overall, the Craftsman 917.274953 lawn mower combines powerful performance, user-friendly features, and durable construction, making it an excellent choice for those seeking to maintain a healthy and attractive lawn. Whether you have a small backyard or a larger landscape, this mower can adapt to your needs, making lawn care a more manageable and enjoyable task.
Top Page Image Contents