Craftsman 917.27475 manual To Sharpen Blade

Page 18

TRACTOR

Alwaysobservesafety ruleswhen per-

forming any maintenance.

BRAKE OPERATION

If tractor requiresmore than five (5) feetto stopat highestspeedin highestgear on a level,dry concreteor pavedsurface,then

brakemust be checkedand adjusted.(See "TOADJUSTBRAKE"in the Serviceand

Adjustmentssection of this manual).

TIRES

•Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rub- ber.

•Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND

REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as de- scribed, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disen-

gaged position.

CHECK OPERATOR PRESENCE

SYSTEM

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" posi- tion and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

ROS "ON" Position Engine "ON" Position (Normal Operating)

•When the engine is running with the ig- nition switch in the ROS "ON" position and the attachment clutch engaged, any at- tempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade

with trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft.

Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Mandrel As,,;embly

g Blade

EdgeCenter

Flat Wash(

Lock WasheE....

Blade Bolt

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause

excessive vibration and eventual damage to mower and engine.

• The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer,

18

follow the instructions supplied with

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Crrftsmrn Limitedwarrantyon Craftsmanridingequipment General Operation IV. Towing ServiceIII. Children Safe Handling of GasolineGeneral Service Product Boot Install Seat Assemble Extension Shaft and BootInstall Steering Wheel To Remove Tractor from CartonCheck Battery To Roll Tractor OFF Skid See Operation section for locationCheck Deck Levelness ChecklistCheck Tire Pressure Check for Proper Position of ALL BeltsAutomatic Models only Know Your Tractor ROS onHOW to USE Your Tractor To SET Parking BrakeStopping Using the Reverse Operation System To Operate MowerReverse Operation System ROS To Operate on Hills Mowing Tips Before Each USE ChartGeneral Recommendations LubricationTo Sharpen Blade Battery EngineTransaxle Cooling AIR Filter Clean AIR ScreenEngine OIL Filter Engine Cooling SystemSpark Plugs CleaningMuffler IN-LINE Fuel FilterTo Install Mower Tractor To Remove MowerTo Level Mower Housing To Replace Mower Blade Drive BeltTo Check Brake To Check and Adjust BrakeTo Adjust Brake To Replace Motion Drive BeltMent To Start Engine with a Weak BAT TeryReplacing Battery Engine Cylinders TractorEngine OIL OtherChoked Troubleshooting ChartCause 3ORRECTION Start EngineProblem CauseCorrection Problem Cause OFFPage Schematic Tractor - Model NumberElectrical KEY Part NO. NO.DESCRIPTION Tractor - Model Number Chassis and Enclosures KEY Part Description Tractor Model Number Ground Drive Tractor - Model Number Ground Drive StltTractor - Model Number Steering Assembly Tractor - Model Number Steering Assembly Optional Equipment Tractor - Model Number Lift Assembly Tractor - Model Number Seat Assembly Decals Tractor - Model Number Mower Deck Shaft 42A REF Part NO. no Description 20@ 305% O47 917.274750 Briggs ENGINE-MODEL Number 31P777, Type Number 0299-E1Tractor Model Number Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXSears

917.27475 specifications

The Craftsman 917.27475 is a lawn tractor that combines power, performance, and versatility, making it an ideal choice for homeowners looking to maintain their outdoor spaces with ease. Equipped with a robust 19 horsepower Briggs & Stratton engine, this model provides reliable starting and efficient performance, ensuring that tackling those large lawns becomes a manageable task.

One of the standout features of the Craftsman 917.27475 is its 42-inch cutting deck, which offers a wide cutting path to handle various terrains. The deck is made of high-quality steel, ensuring durability and a long lifespan. This model also boasts an adjustable cutting height, allowing users to select from various settings to achieve the desired lawn appearance, whether it be a manicured finish or a more natural look.

The tractor's six-speed manual transmission offers users complete control over their mowing speed, enabling them to adjust according to their mowing conditions. Its tight turning radius allows for enhanced maneuverability, making it easier to navigate around flower beds, trees, and other landscaping features, ensuring a clean cut every time.

Comfort is another key feature of the Craftsman 917.27475. It comes with a plush, high-back seat that provides ample support, helping to reduce fatigue during longer mowing sessions. The strategically placed steering wheel and foot pedals ensure that controls are easily accessible, contributing to an enjoyable mowing experience.

Another advantage of this lawn tractor is its versatility. The Craftsman 917.27475 can accommodate various attachments, transforming it into a multi-purpose machine. Whether it's adding a bagger for easy grass collection, a mulching kit for nutrient recycling, or a snow blade for winter use, this tractor can adapt to changing seasonal needs.

Additionally, the model features an easy-to-access fuel tank and a simple maintenance design that allows for hassle-free oil changes and adjustments. With its durable tires designed for traction on various terrains, the Craftsman 917.27475 is built to tackle all types of mowing challenges.

In summary, the Craftsman 917.27475 lawn tractor merges powerful performance with comfort and versatility, making it a valuable investment for homeowners. Its numerous features, combined with ease of use, ensure that maintaining a beautiful lawn is not just a chore but a rewarding experience.
Top Page Image Contents