Craftsman 917.28955 owner manual Mower Drive Belt Removal, Mower Drive Belt Installation

Page 26

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL

1.Park tractor on a level surface. Engage parking brake.

2.Lower attachment lift lever to its lowest position.

3.Disengage belt tension rod (K) from lock

bracket (L).

AUTION: Belt tension rod is spring load- ed. Have afirm grip on rod and release slowly.

4.Remove screws (P) from R.H. and LH. mandrel covers and remove covers (Q).

5.Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

6.Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

1.Install belt around both mandrel pulleys

(R)and around idler pulleys (S) as shown.

2.Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing

in all mower pulley grooves.

3.Reassemble R.H. and LH. mandrel cov- ers (Q). Securely tighten all screws.

4.Engage belt tension rod (K) on locking

bracket (L).

_i, CAUTION: Belt tension rod is spring load- ed. Have atight grip on rod and engage slowly.

5.Raise attachment lift lever to highest position.

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL-

1.Remove mower (See "TO REMOVE

MOWER" in this section of manual). NOTE: Observe entire motion drive belt

and position of all belt guides and keepers.

2.Disconnect clutch wire harness (A).

3.Remove anti-rotation link (B) on right side of tractor.

4.Remove belt from stationary idler (C) and clutching idler (D).

5.Remove belt from centerspan idler (E).

6.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (F).

7.Remove belt downward from engine pulley and around electric clutch (G).

8.Slide belt toward rear of tractor, off the steering plate (H) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steering plate (H) and above clutch brake pedal shaft (J).

2.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

3.Pull belt toward rear of tractor. Care- fully work belt down around transaxle input pulley (F). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (E).

5.Install belt through stationary idler (C) and clutching idler (D).

6.Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

7.Reconnect clutch harness (A).

8.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

9.Install mower (See "TO INSTALL MOWER" in this section of manual).

26

Image 26
Contents CRI Ftsmrn SEARS, Roebuckand CO., Hoffman ESTATES, IL 60179 U.S.ACraftsman Limited Warranty TWO Years on Tractor Days on BatteryGeneral Operation Safe Handling of Gasoline ServiceIV. Towing GENERALSERVlCE Customer Responsibilities Product SpecificationsSears Installation Service Repair ProtectionMower Front Wheel 1/40.D. WasherBefore Removing Tractor To Remove Tractor fromCarton Assemble Front Wheel to MowerINSTALL Mower and Drive Belt Disengage Belt tension rod K from lock Ing bracketCheck for Proper Position Check Tire PressureCheck Deck Levelness Check Brake System@@@ Know Your Tractor Attachment Clutch SwitchService Reminder / Hour Meter Engine HOW to USE Your TractorStopping Mower Blades To SET Parking BrakeTo Operate Mower To Adjust Mower Cutting HeightTo Adjust Gauge Wheels To Move Forward and BackwardTowing Carts and Other ATTACH= Ments Before Starting the EngineTo Transport Check Engine OIL LevelReserve Fuel Valve Operation To Start EngineADD Gasoline Mowing Tips Before Each USE ChartGeneral Recommendations ScheduleTires Check Operator Presence SystemCheck Reverse Operation ROS System Engine To Clean Battery and TerminalsTransaxle Cooling LubricationIN=LINE Fuel Filter To Service CartridgeClean AIR Screen MufflerDeck Washout Port CutionTo Install Mower To Remove MowerPrecision SIDE-TO-SIDE Adjustment Visual SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Level MowerMower Drive Belt Removal Mower Drive Belt InstallationBelt Installation To Replace Motion Drive BeltTo Remove Wheel for Repairs To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BAT- TeryTo Remove Hood & Grill Assembly Engine BatteryTractor OtherCorrection Problem CauseWill not start Problemcause Loss of powerCutting Discharge Headlights not working If so equippedEngine Backfires Battery Will NotWhen Turning Tractor Is shiftedSuggested Guide for Sighting Slopes for Safe Operation INE Only Ride UP and Down Hill Not Across Hill Degrees MAXGARANTiA Limitada DE Craftsman DOS AltOS Para Tractores Funoionamiento General AdvertenoiaIV. Remolque III. NII OSManipulacion Segura DE LA GasolinaPage Producto LA REPARAClONEspecificaciones DEL API-SG-SLMontaje de la pieza BarraAntioscilaci6n De uni6n Deantera Rear Lift LinkLA Corredera Para Hacer Rodar EL TractorFuera DE LA Corredera Vea la sec= ParaInstale Primero LA Barra Anti Balanceo S Instale LA Segadora Y LA Correa DE TRANSMISI6NTaje DE LA Segadora Y DE LA Correa DE Transmision Fije LA Pieza DE Union Anterior EPage Revision DEL Sistema DE Frenos Revision DE LA Presion DE LAS LlantasRevision DE LA Nivelacion DEL Conjunto Jlista DE Revision@@@@ Familiaricese CON SU Tractor Istema DE Funcionamjento HaciaComo Usar SU Tractor MientoLA Segadora Para Operar EN Cerros Funcionamiento AtrasUsar EL Sistema DE Funcionamiento ATR,,S Para TransportarPara Hacer Arrancar EL Motor Agregue GasolinaPara Operar DE LA Valvula DE Gasolina DE Reserva Arranque CON Tiempotem Plado 50/10 Y MASConsejos Para Segar Tabla Recomendaciones GeneralesAntes DE Cada USO DE LubricacionTractor 4rmi Motor LubricacksnLimpieza DE LA Rejilla DE Aire LimpiezaFiltro DE Combustible EN Linea Mmpieza DE LA Entrada DE AIRE/AREAS DE EnfriamentoPuerto DE Lavado DE LA Cubierta ImportantePara Instalar LA Segadora Para Desmontar LA Cortadora DECesped Instalar LA Segadora Y LA Correa DEAjuste DE Delante a ATR,S Para Nivelar LA SegadoraRegulacion Visual DE Lado a Lado Regulacion DE LA Precision DE LadoControl DEL Freno Montaje DE LA Correa DE LA SEGA- DoraControlar Y Ajustar EL Freno Montaje DE LA Correa Para Cameiar LA Correa DE Impulsion DE MovimientoDesmontaje DE LA Correa Impresion / Inclinacion DE LAS Ruedas DelanterasPara Cambiar LA Bombilla DE LA LUZ Delantera Para ADJ U Ntar LOS CAB LES DE EM Palm EReemplazar LA Bateria Entrecierre Y RelesMotor CarburadorAceite DEL Motor OtrosMotor Sistema DE Combustible CilindrosCorreccion ProblemaCausa Estrangulacion ChokeIdentificacion DE Problemas ProblemaLas luz ces delanteras no est.n Cuesta Abajo Y no Atraviese EL Cerro 15GRADOS MAX Operacion SeguraSolamente Ande Cuesta Arriba O Needmore Your Home

917.28955 specifications

The Craftsman 917.28955 is a noteworthy addition to the realm of lawn care equipment, specifically designed for homeowners seeking reliability and efficiency in their mowing tasks. This riding mower combines power, comfort, and innovative technology, making it ideal for those with medium to large lawns.

One of the standout features of the Craftsman 917.28955 is its robust engine. Powered by a 17.5 horsepower Briggs & Stratton engine, this mower ensures ample power for cutting through various types of grass, including thick or wet conditions. The engine's performance is complemented by an automatic transmission, allowing the operator to experience smooth shifting without the hassle of manual adjustments. This feature significantly enhances maneuverability and overall mowing ease.

The design of the mower is user-friendly, with a 42-inch cutting deck that strikes a perfect balance between efficiency and ease of use. This size allows for quicker mowing of larger areas while still enabling access to tighter spots, making it versatile for various lawn layouts. The cutting height can be easily adjusted to six different positions, allowing users to customize their mowing height according to the season or grass type.

Another innovative aspect of the Craftsman 917.28955 is its integrated technology. The mower is equipped with a deck wash system, which simplifies maintenance by allowing users to connect a water hose to the mower's deck for convenient cleaning. Keeping the mower's deck clean ensures optimal performance and longevity.

Comfort is not overlooked in the design of the Craftsman 917.28955. The tractor-style seat is designed to provide a comfortable ride, featuring an ergonomic shape and ample padding. The easy-to-reach controls empower the operator to adjust speeds, cutting heights, and other functions effortlessly, enhancing the mowing experience.

Furthermore, the Craftsman 917.28955 emphasizes safety with features such as the operator presence control, which ensures the mower only operates when the operator is seated. This crucial safety feature helps prevent accidents by automatically shutting off the blades if the operator dismounts the seat.

In summary, the Craftsman 917.28955 is an exceptional riding mower that effectively combines power, user-friendly features, and innovative technology. With its reliable engine, adjustable cutting deck, integrated maintenance systems, and focus on comfort and safety, this mower is poised to meet the diverse needs of modern homeowners looking to maintain their lawns efficiently and effortlessly.