Craftsman 917.273401 To Attach Jumper Cables, Replacing Battery, Interlocks and Relays

Page 27

If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

Weak or Dead Battery Fully Charged Battery

REPLACING BATTERY

_WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift seat pan to raised position.

2.Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable to positive (+) terminal with hex bolt and

keps nut as shown. Tighten securely. Slide terminal cover over terminal

5.Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

Terminal

Keps

NuHex

Bolt

Positive (Red) Cable Negative (Black) Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Hood

adlight Wire

nnector

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Icrrftsmrni Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentII. Slope Operation General OperationIV. Service Do notIII. Children Page Home Sears Installation ServiceCustomer Responsibilities Repair Protection AgreementsSlope Sheet Steering WheelBefore Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyInstall Seat To Remove Tractor fromCheck Battery Check for Proper Position of ALL Belts Install Mulcher PlateCheck Deck Levelness DischargingH L I,,I Attachment Know Your TractorAmmeter Lift Lever PlungerEngine HOW to USE Your TractorTo SET Parking Brake Ground DriveBefore Starting the Engine To Operate MowerTo Operate on Hills Transmission Engaged Transmission DisengagedADD Gasoline To Start EngineAutomatic Transmission Warm UP Mowing Tips Purge TransmissionMulching Mowing Tips General Recommendations Before Each USECheck tire pressure Blade Removal BatteryTractor Operator Presence SystemEngine Transaxle Pump FluidLubrication Clean AIR Screen AIR FilterEngine OIL Filter Protect painted surfaces with auto- motive type wax CleaningMuffler Spark PlugsTo Remove Mower Service or AdjustmentsTo Install Mower TractorTo Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Removal Belt Installation BeltinstallationTo Start Engine with a Weak BAT- Tery Transaxle Motion Control LE VER Neutral AdjustmentTransmission Removal Replacement To Adjust Steering Wheel Align MentTo Replace Fuse Replacing BatteryTo Attach Jumper Cables Interlocks and RelaysTo Adjustthrottle Control Cable To Adjust CarburetorPreliminary Setting Cylinders BatteryFuel System Engine OILTroubleshooting Chart ProblemCause Correction Poor grass CauseMower blades will Not rotateWorking Battery Will NotWhen turning Headlights NotFuel SHUT-OFF Solenoid Tractor - Model Number SchematicTractor - Model Number Electrical KEY Part Description Tractor - Model Number 917.273401 Chassis and Enclosures 208 Tractor - Model Number Chassis and EnclosuresTractor - Model Number Ground Drive KEY Part Description Tractor - Model Number 917.273401 Steering Assembly Tractor - Model Number 917.273401 Steeringassembly Tractor -- Model Number Engine Tractor -- Model Number 917.273401 Seat Assembly Tractor -- Model Number Decals X202O2O Tractor -- Model Number Lift AssemblyTractor - Model Number Mower Deck Tractor - Model Number Mowerdeck 44B 150 115 32 49 106 65 Li 114,i 127 208 183 T85 182 4371D .078W 434 13J OZZCARBURETOROASKETSET121AOVERHAUL KIT Intake 146 691639 Key-Timing 691279 309 693551 Motor-Starter 868 690968 Suggested Guide for Sighting Slopes for Safe Operation Your Home

917.273401 specifications

The Craftsman 917.273401 is a powerful and versatile lawn tractor designed to tackle a variety of landscaping tasks while providing users with a smooth and efficient mowing experience. This model combines robust construction with advanced technologies to meet the needs of homeowners and gardeners alike.

One of the standout features of the Craftsman 917.273401 is its reliable engine. Powered by a 20-horsepower Briggs & Stratton engine, this lawn tractor delivers ample power to handle thick grass and uneven terrain. The engine is designed for easy starts and dependable performance, ensuring users can rely on their mower season after season.

In terms of cutting capabilities, the Craftsman 917.273401 is equipped with a 42-inch cutting deck. This wide deck allows for efficient mowing over medium to large lawns, reducing the time it takes to cover ground. Moreover, the deck is adjustable, providing users with the flexibility to select different cutting heights, ranging from 1.5 to 4 inches. This feature is essential for achieving the desired lawn appearance and accommodating various grass types.

The tractor's transmission system is another highlight, featuring a hydrostatic transmission that offers smooth and effortless speed adjustments. This technology allows users to drive at their preferred pace without the need for manual gear shifting, making the mowing process more enjoyable and less strenuous.

Comfort and usability are prioritized in the Craftsman 917.273401, showcased by its ergonomic seating and user-friendly controls. The high-back seat reduces fatigue during long mowing sessions, while the easy-access dashboard ensures that all necessary controls are within reach. Additionally, the tractor is designed with a tight turning radius, enabling users to maneuver around obstacles and tight spaces with ease.

Furthermore, the Craftsman 917.273401 is compatible with various attachments and accessories, such as baggers, snow plows, and mulching kits. This versatility extends the lawn tractor's utility beyond mowing, allowing users to tackle different tasks throughout the year.

In summary, the Craftsman 917.273401 stands out in the realm of lawn maintenance with its powerful engine, adjustable cutting deck, hydrostatic transmission, and user-centric design. Whether you're mowing a suburban lawn or managing a larger property, this lawn tractor offers the features and performance necessary to achieve a well-groomed landscape with ease.
Top Page Image Contents