Craftsman 917.273631 manual 00272

Page 16

COLD WEATHER STARTING ( 50 ° F and below)

6.When engine starts, leave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, imme- diately move the throttle control to the

fast position. Engine warm-up may take from several seconds to several

minutes (the colder the temperature,

the longer the warm-up).

The attachments can also be used dur- ing the engine warm-up period.

NOTE: If at a high altitude (above 3000

feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance

(see "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual).

MOWmNG TIPS

Mower should be properly leveled for

best mowing performance. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has already been

cut. Have the cut area to the right of the tractor. This will result in a more

even distribution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished.

f

J

J

00272

If grass is extremely tall, it should be mowed twice to reduce load and pos- sible fire hazard from dried clippings.

Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the at- tachment being used.

MULCHmNG MOWmNG TIPS

mMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean after each use.

The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recut- ting action of the blades.

Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, the newly cut area will not be exposed to direct sunlight.

o For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades. For extremely heavy grass, re- duce your width of cut on each pass and mow slowly.

MAX 1/3

Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a sec-

ond cut, mow across (perpendicular) to the first cut path.

Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This will help prevent matting and graining of the lawn.

16

Image 16
Contents Craftsmiin Limitedwarrantyon Craftsmanridingequipment Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, ILSlope Operation Taft grass can hide obstacles Do notPage IAPFSG-SL RC12YCPSI U1ROil Drain Tube For Future Use Adjust Seat HOW to SET UP Your Tractor Check BatteryTo Remove Tractor from Carton Unpack Carton Reposition RmGHT Rear Gauge ALL Belts Check for Proper POSmTmONCheck Brake System @@@@ Know Your Tractor STOPPmNG To Adjust Gauge Wheels To TransportTo Operate Mower To Operate on HillsADD Gasoline Before Starting the Engine Check Engine OIL LevelTo Start Engine 00272 Ervcdates Before Each USETractor Operator Presence SystemBlade Care Blade RemovalTo Clean Battery and Terminals Transaxle CoolingBatt E RY To Change Engine OILIiuffler Spark PlugsTractor To Remove Mower SIDE-TO-SIDE Adjustment with Bubble Level Alternate SIDE-TO-SIDE Adjustment MethodBelt Installation To Check and Adjust BrakeTo Adjust Brake Both Front Links Must be Equalin LengthTransaxle Gear Shift Lever NEU- Tral Adjustment MentFront Wheel TOE=IN/CAMBER To Remove Wheel for RepairsTo Remove Hood and Grill AS- Sembly To Adjust Carburetor Preliminary SettingFinal Setting Acceleration TestFuel System Engne OILCause CORRECTmON Engine ContinuesTo run when Operator Leaves Seat With attach Ment Clutch EngagedProblem Cause Battery wiii not chargeCORRECTmON Mower blades wiii Remove Obstruction Not rotateTractor o o Model Number SCHEMATmC BlackJ21 Tractor - Model NumberElectrical Tractor o o Model Number ELECTRmCALTractor o o Model Number 917.273631 CHASSmS and Enclosures Tractor ooMODEL Number 917.273631 CHASSmSAND Enclosures KEY PartTractor - Model Number Ground Drive Tractor Model Number Ground DRmVESTEERmNG KEY Part Optional Equipment DESCRiPTiON Tractor Model Number Seat Assembly KEYDecals Part DescriptionUFT Assembly Tractor - Model Number UFT Assembly KEY Part DescriptionMower Deck KEY Part NO. NO.DESCRIPTION Tractor Model Number DANATRANSA×LE==MODELNUMBER4360 EMD Dana TRANSAXLE==MODEL Number 4360 EMD LOO8 144I 947 Intake 267 695134 Screw Casing Clamp 691279 Tractor ooMODEL Number Page Suggested Guide for Sighting Slopes for Safe Operation Iiiiiiiiiiiiiiiiiiii CanadaIiiiiiiiiiiiiiiiiii Rev 7.6.04 TRiMH