Craftsman 917.27191 To Convert to Bagging or Discharging, Check Tire Pressure, Check Brake System

Page 10

INSTALL MULCHER PLATE (If previously removed)

1.Raiseand hold deflectorshield in upright position.

2.Placefront of mulcher plate over front of mower deck opening and slide into place, as shown.

3.Hook front latch into hole on front of mower deck.

4.Hook roar latch into hole on back of mower deck.

Deflector

Mulcher

 

Shield _

Plate

Latch

Hooks

_CAUTION: Do not remove deflector shield from mower. Raise and hold shield

when attaching mulcher plate and allow it to rest on plate while in operation.

TO CONVERT TO BAGGING OR DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change blades. The mulcher blades are de-

signed for discharging and bagging also.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is properly adjusted. See "TO ADJUST

BRAKE" in the Service and Adjustments section of this manual.

/CHECKLIST

Before you operate and enjoy your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product.

Please review the following checklist: ,/All assembly instructions have been

completed.

/ No remaining loose parts in carton.

/Battery is propedy prepared and charged. (Minimum 1 hour at 6 amps).

/ Seat is adjusted comfortably and tightened securely.

,/All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

/Be sure mower deck is properly leveled side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

/Check mower and ddve belts. Be sure they are routed properly around pulleys and inside all belt keepers.

/Check wiring. See that all connections

are still secure and wires are properly clamped.

While learning how to use your tractor, pay extra attention to the following important items:

,/Engine oil is at proper level. ,/Fuel tank is filled with fresh, clean,

regular unleaded gasoline.

,/Become familiar with all controls - their

location and function. Operate them before you start the engine.

/Be sure brake system is in safe operating condition.

10

Image 10
Contents CRAFT.TMANI Product Specifications WarrantySafety Rules Assembly/Pre-OperationGeneral Operation II. Slope OperationDo not IV. ServiceIII. Children Page RC12YC Product SpecificationsRepair Agreement UIRSteering Wheel Check Battery Tools Required for AssemblyTo Remove Tractor from Carton Unpack Carton Install Seat Check Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsENG,,EONENG,NEOFFO,LPRSREOG,-nSONOVEPI Knowyour Tractor Stopping HOW to USE Your TractorTo USE Choke Control To Stop Mower Blades To Adjust Gauge WheelsDisengage attachment clutch control Check Engine OIL Level Before Starting the EngineADD Gasoline To Start EngineMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication Chart=.F. R Before Each USEOperator Presence System Brake OperationTires Blade CareEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower To Remove MowerTo Replace Mower Blade Drive Belt SIDE-TO-SIDE AdjustmentBelt Installation Belt RemovalTo Adjust Brake Belt InstallationTo Replace Motion Drive Belt Werya To Replace Headlight Bulb To Remove Hood and Grill AssemblyReplacing Battery Interlocks and RelaysTo Adjust Carburetor To Adjust Choke ControlEngine Battery OtherCause ProblemCorrection Problem Cause Correction Faulty light switch Blades improperly installedSwitch is OFF Bad battery cellsSchematic Tractor --MODEL NumberTractor -- Model Number Electrical Tractor - Model Number Electrical KEY Part DescriptionTractor - Model Number 917.271910 Chassisand Enclosures KEY Part NO. no Description Tractor - Model Number Grounddrive Keeper, Belt,Engine, Fool-Proof Tractor - Model N UM BER SteeringTractor - Model Number Steering KEY Part DescriptionOptional Equipment Tractor - Model NumberKEY Part NO. NO. Description Tractor - Model Number Liftassembly Tractor - Model Number Seat Assembly Decals Wheels and TiresKEY Part Description NO. no Tractor - Model Number Mowerdeck Tractor - Model Number Mower Deck NtJMBERS Here Bevel & Spur Gear 30 Tractor -- Model Number IOOWNERS.IUBRIGGS& STRArroNENGINE-MODELNUMBER407777,TYPE NUMBER0167-E1 Valve Gasket SET Gasket-Roat Bowl Tractor -- Model Number KEY Part NO. NO.DESCRIPTIONPage Page Sighting Only Ride UP and Down HillNot Across Hill SKY Line or TreeOr Sears Maintenance Agreement Canada 181312 3.13.02 TR