Craftsman 917.273763 owner manual Howto SET UP Your Tractor, Tools Required for Assembly

Page 8

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need

are

listed

below.

 

 

(1)

3/4"wrench

(1)

Pliers

(2)

7/16"wrench

(1)

Utility knife

(1)

Tire

pressure

gauge

 

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating posi- tion (seated behind the steering wheel).

_-

1/2 Hex Nut

_

Insert

 

Large Flat

 

Washer

Steering

g

Wheel

Boot

 

7Tabs

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat.

3.Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

1.Slide extension shaft onto lower steer-

ing shaft. Align mounting holes in ex- tension and lower shafts and install 1/4

hex bolt and Iocknut. Tighten securely. IMPORTANT: Tighten bolt and nut se- curely to 10-12 ft. Ibs torque.

2.Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3.Position front wheels of the tractor so they are pointing straight forward.

4.Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5.Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6.Assemble large flat washer, 1/2 hex nut and tighten securely.

7.Snap steering wheel insert into center of steering wheel.

Adapter_

Shaft

8.Remove protective materials from trac- tor hood and grill.

IMPORTANT: Check for and remove any

staples in skid that may puncture tires where tractor is to roll off skid.

HOWTO SET UP YOUR TRACTOR

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

2.Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3.Place seat on seat pan so head of shoulder bolts are positioned over the large slotted holes in pan.

4.Push down on seat to engage shoulder

bolts in slots and pull seat towards rear of tractor.

8

Image 8
Contents Crrftsmrni Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation II. Slope OperationIII. Children IV. ServiceDo not Page Repair Protection Agreements Sears Installation ServiceCustomer Responsibilities Steering Howto SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Before Removing Tractor from Skid Attach Steering WheelCheck Battery AdjInstall Mulcher Plate Check Deck LevelnessTo Convertto Bagging or Discharging Check for Proper Position of ALL BeltsH L I,,I Know Your Tractor HOW to USE Your Tractor To SET Parking BrakeTo Move Forward and Backward Ground DriveTo Adjust Gauge Wheels To Operate on HillsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatictransmissionwarmup Purge TransmissionMowing Tips Mulching Mowing TipsGeneral Recommendations Before Each USEBattery Operator Presence SystemBlade Removal To Sharpen BladeLubrication Transaxle Pump FluidBelts Clean AIR Screen Spark PlugsCleaning Protect painted surfaces with automotive Type waxService or Adjustments To Install MowerTractor To Remove MowerBelt Removal To Level Mower HousingSIDE-TO-SIDE Adjustment Belt Installation To Check and Adjust BrakeTo Adjust Brake To Check BrakeTransaxle Motion Control LE- VER Neutral Adjustment Transmission Removal ReplacementTo Adjust Steering Wheel Align Ment To Remove Wheel for RepairsReplacing Battery Interlocks and RelaysTo Replace Fuse To Remove Hood and Grill AS- SemblyTo Adjustthrottle Control Cable To Adjust CarburetorPreliminary Setting EngineFuel System BatteryTractor Troubleshooting Chart ProblemCause VibrationSlow OFFTractor - Model Number Schematic O111LACKTractor - Model Number Electrical KEY Part Description Tractor - Model Number 917.273763 Chassis and Enclosures Tractor --MODEL Number Chassis and Enclosures 212 Insert Lens ReflectiveTractor - Model Number Ground Drive Tractor -- Model Number Ground Drive 561Tractor - Model Number 917.273763 Steering Assembly Tractor - Model Number 917.273763 Steeringassembly Tractor - Model Number Engine KEY PartTractor - Model Number Seat Assembly Tractor - Model Number Decals Wheels & TiresTractor - Model Number Lift Assembly Tractor - Model Number Mower Deck KEY Part NO. no Description Zr- c Tractor Model Number Hydro Gear Transaxle - Model Number437 084 \WZI o1lo= ql 13o03 31oi 7,,9 Governor Crank Tractor - Model Number Label-EmissionsSuggested Guide for Sighting Slopes for Safe Operation 6E/ R

917.273763 specifications

The Craftsman 917.273763 is a powerful and versatile lawn mower designed to meet the needs of residential users seeking reliability and performance. This machine stands out in the crowded market of lawn care equipment due to its robust features, advanced technology, and user-friendly design.

One of the primary characteristics of the Craftsman 917.273763 is its efficient 25-horsepower engine. This powerful engine ensures that the mower can easily handle thick grass and challenging terrain, providing a clean and even cut every time. The mower's cutting deck measures 54 inches, which strikes a balance between maneuverability and efficiency. This size allows users to cover larger areas in less time, making it an excellent choice for homeowners with expansive lawns.

The cutting height is adjustable, enabling users to select from multiple cutting positions based on their lawn's needs. This flexibility not only promotes healthier grass growth but also accommodates different landscaping styles. The mower is equipped with a dual-blade system, which enhances grass cutting performance and helps to produce fine clippings that can be left on the lawn as natural mulch.

One of the standout technologies in the Craftsman 917.273763 is its electronic ignition system, which provides reliable starting performance every time. This innovation eliminates the guesswork often associated with traditional ignition systems and enhances overall ease of use. Additionally, the mower comes with a hydrostatic transmission, which offers smooth and effortless speed adjustments. Users can shift seamlessly from forward to reverse, a feature that greatly enhances maneuverability, especially in tight spaces.

Comfort is another key aspect of this mower's design. The operator's seat is cushioned and adjustable, allowing users to find their preferred position for prolonged mowing sessions. The steering wheel is ergonomically designed, and controls are within easy reach, making it user-friendly for individuals of all ages.

Safety features are also integral to the Craftsman 917.273763. It includes blade brake technology, ensuring that the mower's blades stop within seconds of releasing the drive lever. This feature significantly reduces the risk of accidents.

In summary, the Craftsman 917.273763 stands out due to its powerful engine, adjustable cutting capabilities, comfortable design, and advanced technologies. Whether managing a small yard or a larger property, this mower delivers the performance and reliability homeowners need for maintaining a pristine lawn.