Craftsman 917.271815 To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 27

REPLACING BATTERY

_CAUTION: Do not short battery terminals by allowing a wrench or any

other object to contact both terminals at

the same time. Before connecting battery, remove metal bracelets, wristwatch

bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to

positive (+) battery terminal with hex bolt and keps nut as shown. Tighten

securely.

7.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut.

Tighten securely

8.Close terminal access doors.

9.Close hood.

 

Keps

Terminal

Hex

 

Access _.,_i.

 

 

Positive

:"

Cable

Terminal

Negative

Guard

Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward enaine and lift off of tractor.

4.To replace, reverse above procedure.

Headlight

Wire Connector

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems,

which are being done at the customers expense, may be performed by any non- road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the

factory and adjustment should not be

necessary. Check adjustment as de- scribed below before loosening cable. If adjustment is necessary, proceed as

follows:

1.With engine not running, move throttle control lever to fast position.

2.Check that swivel is against side of quarter circle. If it is not, loosen cable clamp screw and pull cable back until swivel is against quarter circle. Tighten cable clamp screw securely.

Clamp Scre_

Quarter _€_rcle_,_

._ _

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Craftsmiihi Limited 90 DAY Warranty on Battery II. Slope Operation General OperationIV. Service III. ChildrenDo not Page Customer Responsibilities Repair AgreementSeat Before Removing Tractor From Skid Attach Steering Wheel Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonFunction of controls Install SeatCheck Deck Levelness Install Mulcher PlateDischarging Check Tire PressureChecklist Free Wheel Plunger Know Your TractorTo USE Throttle Control HOW to USE Your TractorTo SET Parking Brake StoppingShoulder To Adjust Mower Cutting HeightTo Adjust Gauge Wheels To Operate Mower To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsTo Start Engine Mulching Mowing Tips Mowing TipsBefore Each USE Maintenance ScheduleLubrication Chart General RecommendationsBlade Removal Brake OperationOperator Presence System Blade CareTransaxle Cooling BatteryEngine BeltsIN-LINE Fuel Filter Clean AIR ScreenMuffler Spark PlugsTo Remove Mower CleaningTo Install Mower TractorBelt Removal To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Adjust Brake Transaxle Gear Shift Lever Neutral AdjustmentTo Replace Motion Drive Belt To Attach Jumper Cables To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Replace Fuse To Remove Hood and Grill AssemblyTo Replace Headlight Bulb Interlocks and RelaysAcceleration Test To Adjust Choke ControlPreliminary Setting Final SettingEngine OIL BatteryTractor Fuel SystemTroubleshooting Chart ProblemCause Correction Engine valves out of adjustment Problem Cause SlowOFF Your Tractor iS Tractor --MODEL NU Mber26I Electrical 163465 Battery 12 Volt 28 AMPWire Loop Tractor --MODEL NU MB ERTractor Model Number Chassis and Enclosures Tractor -- Model Numb ER Chassis and Enclosures Tractor -- Model NU Mber Ground Drive Bolt, Hex 7/16-20 Belt, Center Span All component dimensionsTransaxle See Breakdown Peerless 206-545CSteering TRACTOR-- Model Number175131 Axle Assembly Tractor --MODEL N Umber6855M Engine 144069 Tractor Model NU MberThrot Paddle 17720408Tractor --MODEL Number Seat Assembly Tractor -- Model NU Mber DecalsWheels and Tires Tractor -- Model Number Lift Assembly Tractor --MODEL Number Lift Assembly Lift Lever Inner Wire Assembly17 165689 Trunnion Tractor --MODEL Number Mower Deck Tractor -- Model Number7O 8A 792085A Dowel PinBearing 5/8 792076A LeverPage 297 643 3341 267 Engine Gasket SET LABEL-EMISSIONKEY Part NO. no Wrench-Spark Page Page Suggested Guide for Sighting Slopes for Safe Operation Sears.RoebtxkandCo Www,larco11

917.271815 specifications

The Craftsman 917.271815 is a powerful and efficient riding mower designed to meet the demands of homeowners who want to maintain a well-groomed lawn with ease. This mower is equipped with a rugged and reliable engine, ensuring consistent performance and longevity. With its user-friendly design and innovative features, the 917.271815 stands out as a top choice for landscaping tasks.

One of the main features of the Craftsman 917.271815 is its robust engine. Powered by a 21-horsepower Briggs & Stratton engine, this riding mower provides ample power to tackle tough terrains and thick grass with minimal effort. The engine's innovative technology promotes efficient fuel consumption, allowing users to mow larger areas without frequent refueling.

The mower’s cutting deck is another highlight. It features a 42-inch cutting width, allowing for a wide mowing path that reduces the time spent mowing. The adjustable cutting height, ranging from 1 to 4 inches, gives users the flexibility to achieve the desired lawn height, ensuring a professional-looking finish.

Ergonomically designed for comfort, the Craftsman 917.271815 features a high-back commander’s seat, providing excellent support during extended mowing sessions. The intuitive control layout, including a sleek steering wheel and foot pedal operation, enhances maneuverability, making it easy to navigate around obstacles in the yard.

Safety is paramount in the design of the 917.271815. It incorporates several safety features, including an automatic safety shut-off that activates when the operator leaves the seat. This technology prevents accidents and enhances user safety while mowing.

The mower's durable construction ensures it can withstand the rigors of regular use. With heavy-duty materials used throughout, the Craftsman 917.271815 is designed to resist wear and tear, reducing the need for frequent repairs. Additionally, the mower features a reliable transmission system that allows for smooth operation and easy shifting between speeds.

Another significant aspect is the mower's versatility. It can be equipped with various attachments, transforming it into a multi-functional tool for various yard tasks, such as leaf collection, snow removal, and more.

Overall, the Craftsman 917.271815 is a well-rounded riding mower that combines power, comfort, and versatility, making it an excellent choice for homeowners looking to maintain their lawns efficiently. With its advanced features and durable design, it promises to deliver top performance season after season.
Top Page Image Contents