Craftsman 917.27105 manual Install Seat, To Drive Tractor OFF Skid

Page 8

Label

Seat

Terminal

Battery

Door

INSTALL SEAT

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan and assemble shoulder bolt. Tighten shoulder bolt securely.

•Assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

Seat

Shoulder Seat Pan

Bolt

Flat Washer

Adjustment

Knob

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location end

function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Rol{ tractor forward off skid.

•Remove banding holding discharge guard up against tractor.

TO DRIVE TRACTOR OFF SKID

(See Operation section for location and function of controls)

_WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to =OFF" position. Continue with the instructions that follow.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Rrftsmrn Limitedtwo Year Warrantyon Craftsmanriding Equipmentparts Children General OperationDo not Service Machine. Taft grass can hide obsta- clesProduct Specifications Keys Video Cassette Slope Sheet Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Rolling Tractor OFF SkidInstall Seat To Drive Tractor OFF SkidTo Convert to Bagging or Discharging Check Tire PressureCheck Brake System Check Deck LevelnessForward Knowyour Tractor HOW to USE Your Tractor To USE THROI-FLE ControlTo Operate Mower To Operate on HillsTo Transport Before Starting the Engine Check Engine OIL LevelTo Start Engine AddgasolineMowing Tips Mulching Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Tractor Engine Transaxle CoolingClean AIR INTAKE/COOLING Areas MufflerAIR Filter Spark PlugsTo Remove Mower CleaningTo Install Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentTo Adjust Brake To Replace Motion Drive BeltNeutraladjustment To Adjust Steering Wheel AlignmentTransaxle Gear Shift Lever Front Wheel TOE-IN/CAMBERReplacing Battery To Remove Hoodand Grill AssemblyTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable To Adjust CarburetorAcceleration Test Battery EngineCorrection ChartProblem Cause Problem CauseTroubleshooting Chart Problemcause DischargeTractor - Model Number Schematic LJltTractor - Model Number Electrical Tractor --MODEL Number ElectricalTractor - Model Number Chassis and Enclosures 208KEY Part Description Tractor - Model Number Ground Drive 116 169 1702 261Dimensions given in U. S Transaxle See BreakdownBolt, Hex 7/16-20 206-545CTractor - Model Number 917.271050 Steering Assembly KEY Part NO. no Engine Tractor - Model NumberOptional Equipment 79 M740108025 Bolt Hex KEY Part NO. NO.DESCRIPTION16 STD551231 Washer Tractor - Model Number Seat Assembly 140122121248X Bushing Snap BIk Nyl 50 Id 140551 145OO6Wheels & Tires Tractor - Model NumberDecals Tractor - Model Number Lift Assembly Inch = 25.4 mm 159460 Washer159471 119 114 115 117 TRACTOR-- Model Number Mower Deck106 , 102 Mower Deck Assembly 144959 Belt Bolt Hardened 130794 Mandrel Assembly Includes165892 STD624008150 70 BA Part Description Spacer+ Ittt .,o-i I..-./1 Fuel System J Cylinder HEAD, Valve and Breather Crankcase Starting System Blower Housing and Baffles KEY Part NO. NO.DESCRIPTION AIR Intake KEY Part NO. NO.DESCRIPTIONNotillustrated Crankshaft KEY Part NO. NO.DESCRIPTIONFuel System KEY Part NO. no Cylinder HEAD, Valve and BreatherDescription KEY Part 41-518-34Crankcase KEY Part NO. no Ignition / Electrical KEY Part NO. NO.DESCRIPTIONOIL PAN / Lubrication KEY Part Description Page Page Page Only Ride UP and Down Hill Not Across HillSighting GuidePart 6 a.m.- 11 p.m. CST SearsPara pedir servicio de reparaci6n a domicilio Sears, Roebuck and Co
Top Page Image Contents