Craftsman 917.270822 Coldweatherstarting 50 Fand Below, Automatic Transmission WARM-UP

Page 16

COLDWEATHERSTARTING (50 ° FAND

BELOW)

When engine starts, slowly push choke

control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the en- gine to accept small changes in speed and load, until the choke control is fully

in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending

on the temperature.

AUTOMATIC TRANSMISSION WARM-UP

Before driving the unit in cold weather

the transm ssion should be warmed up as follows:

Be sure the tractor is on level ground.

Place the motion control lever in neu- tral. Release the parking brake and

let the clutch/brake slowly return to operating position.

Allow one minute for transmission to warm up. This can be done during the engine warm up period.

The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: A high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance.

See 'q'OADJUST CARBURETOR" in the

Service and Adjustments section of this manual.

PURGE TRANSMISSION

A('_CAUTION; Never engage or disen- gage freewheel lever while the engine is

running.

To ensure proper operation and perfor- mance, it is recommended that the trans-

mission be purged before operating trac- tor for the first time. This procedure will re- move any trapped air inside the transmis-

sion which may have developed during shipping of your tractor.

IMPORTANT: Should your transmission require removal for service or replace- ment, it should be purged after reinstalla- tion before operating the tractor.

Place tractor safely on level surface with engine off and parking brake set.

Disengage transmission by placing freewheel control in freewheeling posi- tion (See "TO TRANSPORT" in this sec- tion of manual).

Sitting in the tractor seat, start engine. After the engine is running move thrott e control to slow position. With

motion control lever in neutral (N) posi- tion, slowly disengage clutch/brake pedal.

Move motion control lever to full for- ward position and hold for five (5) sec-

onds. Move lever to full reverse positior and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air

is being removed from hydraulic drive system.

Move motion control lever to neutral (N_ position. Shut off engine and set park- ing brake.

Engage transmission by placing free-

wheel control in driving position (See 'qO TRANSPORT" in this section of

manual).

Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) posi- tion, slowly disengage clutch/brake pedal.

Slowly move motion control lever for- ward; after the tractor moves approxi- mately five (5) feet, slowly move motion control lever to reverse position. After

the tractor moves approximately five (5) feet return the motion control lever to

the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

Your tractor is now purged and ready

for normal operation.

MOWING TIPS

Mower should be properly leveled for best mowing performance. See 'q'O

LEVEL MOWER HOUSING" in the Ser-

vice and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has been cut. Have

the cut area to the right of the tractor. This will result in a more even distribu-

tion of clippings and more uniform cut- ting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds

mow in the opposite direction making left hand turns until finished.

16

Image 16
Contents Help Line SearsPm, Mon Sat Limited 90 DAY Warranty on BAI-FERY Service Slope OperationChildren Do notSafety is Involved Birth defects, or other reproductive harmMaintenance Agreement Product SpecificationsCustomer Responsibilities Batiery16 x Hex Bolt Lackwasher 3/8 Large Flat Washer 16 x 3/4 x 16 Gauge LockSteering Mulcber Plate VideoParts Bag Howto SET Upyour Tractor Tools Required For AssemblyBefore Rolung Tractor OFF Skid AI-IACHSTEERING WheelInstall Mulcher Plate Install SeatTo Drive Tractor OFF Skid To Convert to Bagging or Discharging Check Brake SystemCheck Tire Pressure Check Deck LevelnessH L Know Your Tractor Knob Brake Motion Freewheel Control LeverHOW to USE Your Tractor To Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportEfore Starting the Engine Check Engine OIL LevelADD Gasoline To Start EngineColdweatherstarting 50 Fand Below Automatic Transmission WARM-UPPurge Transmission Mowing TipsMulching Mowing Tips Lubrication Chart Maintenance ScheduleGeneral Recommendations Before Each USEBrake Operation TiresOperator Presence System Blade CareClean AIR Screen BeltsTransaxle Cooling Transaxle Pump FluidCleaning To Install Mower To Level Mower HousingTo Remove Mower To Adjust Brake Equal in length. Both links should beTo Replace Mower Blade Drive Belt RemovalTo Start Engine with Aweak Battery To Adjust Throttle Control Cable To Remove Hood and Grill AssemblyTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Choke Control To Adjust CarburetorPreliminary SEI-FING Final SE1-FINGEngine CylindersTroubleshooting Chart Problem CausecorrectionProblemcause CorrectionTroubleshooting Chart CauseProblem Loss of driveEo IJ Tractor Model NumberElectrical Tractor - Model NumberTractor - Model Number Electrical4799J 166180 Fuse 73510400 NUtKeps Hex 1/4-20 Unc 14,5491Tractor - Model Number Chassis and Enclosures KEY Part Description Tractor - Model Number Ground Drive Tractor - Model Number 917,270822 Ground Drive Tractor --MODEL Number Steering Assembly Tractor - Model Number Steering Assembly Optional Equipment EngineSpark Arrester Tractor - Model Number Engine KEY Part NO. no Tractor - Model Number Seat AssemblyKEY Part Part KEY Description Wheels & Tires KEYTractor - Model Number Lift Assembly Nut, Special Mower Deck BracketAssembly,Sway Bar Spring,Torsion Brakes BracketAssembly,Sway Bar164961 155046Tractor - Model Number Hydro Gear Transaxle - Model Number Housing,Lower Assembly,Upper HousingDifferentialAssembly Ring,Wire Retaining 142961 Seal 75 x 1.25 x Ring, Retaining535 615 24 634A 55225 J 601 534 642 643 523 525 i 284A 1611358 18611121 51A801 783 8O2803 653 209A 414 207 y 307 592 8A5729 10A 304 881 Label Kiti305 573 308 3O6 307Piston Assembly, Standard Size 497074270884 Gasket, intake Manifold Bushing Mounting332 230674 Nut, Hex 803 497604 Housing,Starter 333 394891 Wire, Stop 851 493880592 92278 615APage Page Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Sighting Guide£ S