Craftsman 917272261 owner manual Tolevelmowerhousing, SIDE-TO-SIDE Adjustment

Page 24

TOLEVELMOWERHOUSING

Adiust the mower while tractor is parked on level ground or driveway. Make sure

tires are properly inflated (See -pROD- UCT SPECIFICATIONS" section of this

manual). If tires are over or undednflated, you will not propedy adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A* on both sides of mower should be the same or within 1/4" of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten I_ link adjustment nut on that side.

To lower one side of mower, loosen lift

link adiustment nut on that side. NOTE: Each full turn of adjustment nut will change mower height about 1/8".

Recheck measurements after adjust-

ing.

 

BottomEdgeof

BottomEdgeof

Mowerto Ground

Mowerto Ground

Suspen_Don

Lilt Link

Adjustment

Nut

Before making any necessary adjust- merits, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut "E" on both front links an equal number of turns.

When distance "D" is 1/S" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten nut "E" on both front links an equal number of turns.

When distance "D" is 1/8* to 112"ower

at front than rear, tighten nut =F"against trunnion on both front links.

Recheck side-to-sideadiustment.

o

BOTH FRONT LINKS MUST BE EQUAL

IN LENGTH

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to- side.If the following front-to-back adjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the frontis approximately 1/8" to 1/2" lower than the rear when the mower Is in

its highest position.

Check adjustment on right side of tractor. Measure distance =D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

Front Plate

Trunnion

Assembly

 

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL

1.Park tractor an a level surface. Engage parking brake.

2.Lower mower to its lowest position.

3.Disengage belt tension rod from lock bracket.

ACAUTION: Rod Is spdng loaded. Have a firm grip an rod an release slowly.

4.Remove screws from R.H. mandrel cover and remove cover.

24

Image 24
Contents Lawn Tractor Sears, Roebuck and Co., /817 WA, Hoffman Estates, IL General Operation I1. Slope Operation Do notIV. Service III. ChildrenSafety is Involved Heavy of a load, while on a slope, isCancer and birth defects or other repro- ductive harm Read and observe the safety rules OFILTER3.75PINTSReverse Repair Agreement=.oosRo,,e .-IIIIIIIlllllll!l!llllllll=,B Brackets.oxBolts Tools Required for Assembly Install SeatTo Removetractor from Carton Unpack Carton Attach Steering WheelAssemble Gaugewheelsto Mower Deck To Attach Nose Roller Checktire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemMowerli Our tractors conform to the safety standards of the American Howto Useyourtractor to SET Parking Brake Stopping Mower BladesGround Drive EngineTo Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportTo Start Engine ViscosityADD Gasoline Warm Weather StartingPurgetransmission MowingtipsMaintenanceschedule Lubrication ChartGeneral Recommendations Before Each USETractor To Clean Battery and Terminals BeltsTransaxle Cooling Transaxle Pump FluidClean AIR Screen To Service PRE-CLEANERAIR Filter Engine OIL FilterCleaning MufflerSpark Plugs IN-LINE Fuel FilterTo Install Mower Tractor To Remove MowerTolevelmowerhousing SIDE-TO-SIDE AdjustmentBoth Front Links Must be Equal Length To Adjust Brake To Replace Mower Blade Drive BeltTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive BeltTransmission REMOVAIJREPLACE- Ment Front Wheel TOE-IN/CAMBERReplacing Battery To Attachjumper CablesTo Remove CABLES, Reverse Order To Replace Headlight LampTo ADJUSTTHROnLE Control Cable Adjustment is necessary, proceed as followsTo Adjust Choke Control To Adjust CarburetorTractor BatieryEngine Fuel System Engine OILTroubleshootingchart CauseCorrection Troubleshoong Chart ProblemCause CorrectionTroubleshooting Chart OFFSchematic Tractor - Model NumberElectrical Tractor --MODEL Number KEY Part DescriptionTRACTOR- Model Number Chassis and Enclosures Tractor - Model Number 917.272261 Chassis and Enclosures 30 175692X615 Fender/FootrestTRACTOR- Model Number Ground Drive Tractor Model Number Ground Drive 74713TRACTOR-- MODELNUMBER917.272261 Steeringassembly TRACTOR--MODEL Number Steeringassembly KEY Part NO. NO.DESCRIPTIONOptional Equipment Spark Arrester25 175440X505 Cheke Contro TRACTOR--MODELNUMBER917.272261 Seatassembly Decals Wheels &TIRESTRACTORMODELNUMBER917--.272261 Liftassembly TRACTOR- Model Number Liftassembly TRACTOR- Model Number Mowerdeck Tractor - Model Number Mowerdeck MmO Drag 711dxl,15odx.030thkPage 80810T7I 20 m WjtoThrettle Control Page Page Suggested Guide for Sighting Slopes for Safe Operation PART6&m.-11 p.m,,7daysawek 179175 3.22.01 TR

917272261 specifications

The Craftsman 917272261 is a powerful and versatile lawn tractor designed for homeowners who want to maintain their lawns efficiently and effortlessly. This riding mower boasts a variety of features that make it an excellent choice for tackling different yard sizes and types. Its robust build and innovative technologies ensure a reliable performance every time.

One of the main features of the Craftsman 917272261 is its 19 HP Briggs & Stratton engine. This reliable engine provides the necessary power to handle even the toughest mowing tasks, allowing users to navigate through thick grass and uneven terrain with ease. The engine is also designed for fuel efficiency, helping homeowners save on fuel costs while still getting the job done effectively.

The 42-inch cutting deck is another standout feature of the Craftsman 917272261. This wide cutting width allows for efficient mowing, reducing the number of passes required to cover the entire lawn. The cutting deck is also equipped with adjustable heights, offering seven different positions that allow users to customize the height of their grass cut. This feature helps to create a neat and healthy lawn, accommodating various grass types and preferences.

Technologies integrated into the Craftsman 917272261 ensure a smooth and easy operation. The manual transmission system allows users to choose their speed, providing a tailored mowing experience. Additionally, the inching pedal enables gentle speed control, allowing for precise maneuvering around corners and obstacles.

For added convenience, the Craftsman 917272261 includes a comfortable and spacious operator's seat, designed to reduce fatigue during long mowing sessions. The tractor is also equipped with a reinforced frame, making it durable enough to withstand the rigors of regular use.

Several accessories can enhance the functionality of the Craftsman 917272261. Optional attachments such as baggers, mulching kits, and snow blades turn this versatile lawn tractor into an all-season tool, making it capable of tackling a variety of outdoor chores.

In conclusion, the Craftsman 917272261 is a reliable, feature-rich lawn tractor that combines power, efficiency, and user-friendly technologies. Its strong engine, adjustable cutting deck, and comfort-oriented design make it an excellent investment for any homeowner looking to maintain a pristine lawn all year round.