Craftsman 247.797855 manual Sharpeningor Replacingthe Blades, Chipper Blades, Shredding Blade

Page 14

Chute

Hairpin \

Clips,

Clevis

Pins

_-_Hex

Nuts.

 

Washers 4

Screen

Chipper

Chute

Hand Knobs

FIGURE 18.

SHARPENINGOR REPLACINGTHE BLADES

CHIPPER BLADES

®Disconnect spark plug wire and move it away from spark plug.

e Remove the flail screen as instructed in previous section.,

e Remove the chipper chute by removing three hex nuts and washers. A I/2" wrench is required. See figure 18.

NOTE: When reassembling, the cupped washer goes on the bottom of the chipper chute with the cupped side against the chute.

®Rotate the impeller assembly by hand until you locate one of the chipper blades in the chipper chute opening. Remove the blade, using a 3/16" allen wrench on the outside of the blade and 1/2" wrench on the impeller assembly (inside the hous- ing). See figure 19_

e Remove the other blade in the same manner,

@

FIGURE 19.

Replace or sharpen blades. If sharpening, make cer-

tain to remove an equal amount from each blade Reassemble in reverse order.

Make certain blades are reassembled with the sharp edge facing the direction shown in figure 19 (sharp edge is assembled toward the slotted opening in the impeller assembly).

SHREDDING BLADE

The shredding blade may be removed for sharpening or replacement as follows.

e Disconnect spark plug wire and move it away from spark plug.

eLower the hopper assembly° Block up the housing. See figure 204

e Remove the six hex lock nuts and lock washers from the housing weld bolts using a 1/2" wrench° Separate the chipper-shredder into two halves_

®Remove the back-up plate.

NOTE: When reassembling, make certain the open- ing on the back-up p!ate is toward the bottom of the uniL The back-up plate may be reversed to provide a new cutting edge.

Allen

Pii

Sharp

Torque

Wrench

FIGURE 20.

e Loosen the two hand knobs and cupped washers which secure the chute deflector, and raise the chute deflector.

e insert a t/2" or 3/4" diameter pipe through the flail screen into the impeller to keep it from turning, or remove the flail screen and insert a piece of wood (2 x 4) into the chute opening,

e Remove the two outside screws on the blade, using a 3/16" allen wrench and a 1/2" wrench.

eRemove the blade by removing the center bolt, lock washer and flat washer..

14

Image 14
Contents 770-7110H 9192 HorsepowerMulching and Bagging Safety Rules PreparationMaintenance Agreement Oneyear Limited Warranty on Craftsmangas CHIPPER-SHREDDERTable of Contents TOREMOVECHIPPER-SHREDDERFROMCARTOH AssemblyTools Requiredfor Assembly Flat Washer 5/16 LDMake Certain the Spark Plug Attachingthe Upper Guide Assembly=-ATTACHINGTHE Hopper Assembly Assemble this Truss Screw NUT FirstThrottle Meets Ansi SafetystandardsStarter To Stop Ehgihe HOW to USE Your CHIPPER-SHREDDERHopper Assembly No Larger Than Diameter Recommended Or 1 Diameter MaximumColder 32F Warmer Bar Gasand OIL FILL-UPOIL Dipstick DrainTo Startengine To Stop EhgineEngine Spark Plug AIR CleanerDirt and Combustible Debris MufflerRemoving the Flail Screen StorageCHIPPER-SHREDDER Shredding Blade Sharpeningor Replacingthe BladesChipper Blades Enginespeed CarburetoradjustmentFlails Trouble Shooting HOW to Order Replacement PartsRepair Parts 247.797855 Repair Parts 247.797855 710-0157363 Requires Special Tools To INSTALL. see RepairNOo 2OORepair Parts 224270125 Spark Arresting Muffler AssemblyThick 346 298 969967542 272157307 524

79785, 247.797855 specifications

The Craftsman 247.797855 and 79785 models represent the pinnacle of innovation and functionality in outdoor power equipment. Designed for homeowners seeking dependable and efficient lawn maintenance, these mowers embody the principles of durability and performance, which Craftsman has become synonymous with over the years.

One of the standout features of these models is their powerful engine. Equipped with a robust 20 horsepower Briggs & Stratton engine, they deliver a reliable performance capable of handling diverse terrain and tough grass conditions. The automated starting system provides ease of use, allowing operators to get started without the hassle of manual pulls.

Both models boast a 46-inch cutting deck that ensures wider coverage with each pass, reducing mowing time significantly. The deck is constructed with durable materials, designed to withstand prolonged use while providing a clean, even cut for a professional-looking lawn. Additionally, the adjustable cutting heights—ranging from 1.5 to 4 inches—allow users to customize their mowing experience according to the specific needs of their lawn, accommodating both regular maintenance and seasonal variations.

Technology is another area where the Craftsman 247.797855 and 79785 stand out. They feature a hydrostatic transmission system, which offers smooth and responsive operation. This technology makes maneuvering around obstacles effortless, providing a superior driving experience without the need for frequent gear changes.

Comfort has also been prioritized in the design of these mowers. The high-back seat is ergonomically designed to provide ample support during extended mowing sessions, and the presence of an easy-to-use dashboard allows users to monitor critical information such as fuel level and speed intuitively.

Moreover, both models include a mulching capability, enabling users to recycle grass clippings effectively. This not only reduces the need for bagging but also contributes nutrients back into the soil, benefitting the overall health of the lawn.

In summary, the Craftsman 247.797855 and 79785 models are a testament to reliability, power, and user-friendly design. With their combination of a powerful engine, adjustable cutting deck, advanced transmission technology, and thoughtful ergonomic features, they stand as excellent choices for homeowners looking to maintain and enhance their outdoor spaces. Whether tackling small yards or larger landscapes, these mowers provide a seamless lawn care experience that professionals and enthusiasts alike will appreciate.