Craftsman 917.377582 HOW to USE Your Lawn Mower, Engine Zone Control, To Empty Grass Catcher

Page 7

The operationofany lawn mower can reeultin foreign objectsthrownintothe eyes,whichcan resultin severe eye damage. Alwayswear safetyglassesoreye shieldswhileoperating yourlawnmoweror performingany adjust- mentsor _alm. We recommenda wide visionsafety mask overspectaclesor standard safety glasses.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED CONTROL

The engine speed was set at the factory for optimum performance. Speed is not adjustable.

ENGINE ZONE CONTROL

ACAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the risk of

blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.

Your lawnmoweris equippedwithan operatorpresencecontrolbar which requiresthe operatorto be

behindthe lawn mowerhandleto stad and operatethe lawnmower.

TO A'rrACH GRASS CATCHER

cleee itip FRp be

while operating lawn mower.

Liftthe rear door on the mower housing and place the grass catcher frame onto the formed tabs on the rear door hinge bracket.

The grass catcher is secured to the lawn

mower housing when the rear door is lowered onto the grass catcher frame.

&CAUTION: Do not run your lawn mower without clipping deflector or approved grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open.

Hingedoor

bracket

Grass catcher

Formed tabs

TO ADJUST CUTnNG HEIGHT

Raise wheels for low cut and lower wheels for high cut.

Adjust cutting height to suit your require-

ments. Medium position is best for most lawns.

To change cutting height, squeeze adjuster lever toward wheel.Move wheel up or down to suit your requirements. Be sure all wheels are in the same satUng.

NOTE: Adjuster is properly pesitk)ned when plate tab inserts into hole in lever. Also, 9- position adjusters (if so equipped) allow lever to be positioned between the plate tabs.

Lower Wheels for High Cut

TO EMPTY GRASS CATCHER

To removegrasscatcher,reteaseoperator presencecontrolbarto stopengine.

Liftup rear doorand removethe grass catcherby thehandle.

NOTE: Do notdragthe bag when emptying; it willcause unnecessarywear.

Raise Wheels _

P_

 

for Low Cut _

_

Lever

Image 7
Contents £RRFTSMRN Preparation MaintenanceProduct TrainingOperation Maintenance and StorageTo Remove Lawn Mower from Carton Lawn Mower MaintenanceLawn Mower Performance Mowing Lowerposition handle HOW to SET UP Your Lawn MowerTo Install Attachments To Unfold HandleStarter Handle used for starting the engine Lawn mower housing Wheel adjuster on each wheelMeets Cpsc Safety Requirements Know Your Lawn MowerEngine Speed Control HOW to USE Your Lawn MowerEngine Zone Control To Empty Grass CatcherTo Start Engine GASRive Control 3EFORE Starting Engine OILIf a trail of clippings is left on the right Mowing TipsMulching Mowing Tips Before Each USE General RecommendationsLubrication Blade Care Lockwasher Hardened Blade shaft Washer Trailing adapter Grass CatcherEngine Gear CaseTo Change Engine OIL Low To Adjust HandleRear Deflector To REMOVE/REPLACE Drive BeltCarburetor To Assemble Grass CatcherFully seated Lower frame handleEngine OIL CylinderIandle Fuel SystemOther Trouble Shooting Problem Cause CorrectionCause Troubleshooting ChartKEY Part Description Rotary Lawn Mower - Model no Gear Case Assembly Part NumberInch = 25.4 mm Craftsman Rotary Lawn Mower - Model no KEY Part NO. no Craftsman Rotary Lawn Mower - Model noCraftsman Rotary Lawn Mower - Model no KEY Part Model Number Craftsman 4-CYCLE EngineKEY Part NO. no Craftsman 4-CYCLE EngiiKEY Part Description DogSpring Page Page Sears