Craftsman 486.24717 manual Deck Adapter Mower Deck, Adapter Bracket, Nylock Nuts, Washers

Page 15

Position the adapter over the deck opening, and check for fit of cutout as shown in figure 24. Trim cutout, if necessary, to allow tilting of adapter, keeping the fit as close as possible for best vacuum suction.

NOTE: Make sure adapter clears gauge wheels on mower deck

DECK ADAPTER

/

MOWER DECK

Curl on deck may be located outside of adapter or inside depending on deck opening design

FIGURE 24

Holding the adapter bracket and the deck adapter together, position the deck adapter on the mower deck. Keeping the edge of deck adapter as close as possible to the offset in the adapter bracket, see if the slot in the adapter bracket can be aligned with one or two of the deflector holes in your mower deck's discharge opening. If the bracket can not be located correctly using existing holes, it will be necessary to drill one or two 5/16" diameter holes in the deck. See figure 25.

Use existing holes or drill 5/16" diameter hole or holes.

ADAPTER BRACKET

i t

DECK ADAPTER

MOWER DECK

Keep edge of adapter as close as possible to offset in bracket

FIGURE 25

Assemble the adapter bracket to the deck using two 5/16" x 1-1/4" hex bolts, 5/16" flat washers and 5/16" nylock nuts. See figure 26.

NOTE: It may be necessary to use extra 5/16" flat washers to shim under the bracket next to the deck

surface. Ten extra washers have been furnished as shims. See figure 26.

'

.(

2

6"

,

 

) 511 NYLOCK NUTS

®I"

1-._-----(2) 5116" FLAT

WASHERS

ADAPTER BRACKET

"5116" flat washers

5/16" x 1-1/4"

.i_

used

as

needed

for

 

shims

to

adjust

for

HEX BOLT

 

variations

in decks.

FIGURE 26

With deck adapter positioned correctly over the discharge opening, use the adapter bracket as a template and drill three 9/32" diameter holes in the top of the deck adapter. See figure 27.

Bolt deck adapter to bracket using three 1/4" x 3/4" bolts, nylon washers, 1/4" flat washers and 1/4" lock nuts. Nylon washers should be against the inside of the deck adapter. See figure 27.

(3) 1/4" STEEL WASHERS

(3) 114" x 314" HEX BOLTS

FIGURE 27

Assemble end of hose and a hose clamp over the

round opening of deck adapter and tighten clamp. GO DIRECTLY TO THE OPERATION iNSTRUCTiONS

ON PAGE 16.

Call 1-866-576-8388 for missing parts or assembly help

15

DO NOT RETURN TO STORE

 

Image 15
Contents Do not Return to Store CRnFTSMRHAssembly Repair Parts Lists WarrantySafety Rules Storage Full Size Hardware Chart Carton Contents Repair Parts IllustrationsDo not Return to Store To Avoid Serious iNJURY Serial Number Date of Purchase Model NumberXyZAA QTYCart VAC RER Description QTY DescriptionAssembling the Cart Body Removal of Parts from CartonsWheel Axle Flat Washer Truss Head Bolt WheelNylock NUT Bracket 1/4 Nylock NUTAssembling VAC Parts HEX Bolt Flat WasherLoosen 4 bolts 1/4 turn each Flat WASHERf AssemblyStrap X 1-1/4Assembling the Deck Adapter #62468 Tothe Mower Deck Contents of Hardware Pack for Deck AdapterNylock Nuts Deck Adapter Mower DeckUse existing holes or drill 5/16 diameter hole or holes Adapter BracketBefore Starting HOW to Stop Your CHIP-N=VACHOW to Startyour CHIP-N=VAC HOW to USE Your CHIP-N=VACUsing the Chipper Chute Cleaning Before Each USECheck Tire Pressure Sharpening or Replacing Chipper Blades Nylock Nuts Access PlateProblem Possible CausesCorrective Action Cal11-866-576-8388formissingpartsorassemblyhelp Do not Returnto Store 27.20 REE DescriptionAdapter #62468 Repair Parts for Model 486.24717 Professional CHIP-N-VACQTY DESCRiPTiONQTY.DESCRiPTiON Description QTY IMPELLER Housing AssemblyOnly Ride UP and Down Hill Not Across Hill Degrees MAX LineMY-HOME