Craftsman 247.795950 manual Storage, Service & Adjustment, Removing the Flail Screen

Page 13

STORAGE

Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more.

WITH FUEL IN THE FUEL TANK INSIDE

WARNING: NEVER STORE MACHINE

OF BUILDING WHERE FUMES MAY REACH AN OPEN FLAME OR SPARK, OR

WHERE IGNITION SOURCES ARE PRESENT SUCH AS HOT WATER AND SPACE HEATERS, FURNACES, CLOTHES DRYERS, STOVES, ELECTRIC MOTORS, ETC.

NOTE: A yearly check-up by your local Sears Service Center is a good way to make certain your chipper- shredder will provide maximum performance for the next season.

CHIPPER-SHREDDER

•Clean the chipper-shredder thoroughly.

•Wipe unit with an oiled rag to prevent rust (use a light oil or silicone).

ENGINE

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL

OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARA- TION AND FORMATION OF ACIDS DURING STOR- AGE. ACIDIC GAS CAN DAMAGE THE FUEL SYS- TEM OF AN ENGINE WHILE IN STORAGE.

•Drain the fuel tank.

•Start the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or stor- age container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carbure- tor if using fuel stabilizer.

•Drain all the oil from the crankcase (this should be done after the engine has been operated and is still warm) and refill the crankcase with fresh oil.

•If you have drained the fuel tank, protect the inside of the engine as follows. Remove spark plug, pour approximately 1/2 ounce (approximately one table- spoon) of engine oil into cylinder and crank slowly to distribute oil. Replace spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•Store unit in a clean, dry area. Do not store next to corrosive materials, such as fertilizer.

NOTE: If storing in an unventilated or metal storage shed, be certain to rustproof the equipment by coating with a light oil or silicone.

SERVICE & ADJUSTMENT

WARNING: ALWAYS STOP ENGINE AND

MOVE IT AWAY FROM SPARK PLUG DISCONNECT SPARK PLUG WIRE AND

BEFORE PERFORMING ANY ADJUST- MENTS OR REPAIRS.

REMOVING THE FLAIL SCREEN

If the discharge area becomes clogged, remove the flail screen and clean area as follows.

•Stop the engine, make certain the chipper-shredder has come to a complete stop and disconnect spark plug wire from the spark plug before unclogging the chute.

Loosen the two hand knobs on each side of the chute deflector. Lift the chute deflector up, and tie it out of the way.

•Remove two hairpin clips from the clevis pins which extend through the housing. Remove the clevis pins. Lift the flail screen from inside the housing. See figure 19.

•Clean the screen by scraping or washing with water. Reinstall the screen.

NOTE: Be certain to reassemble the flail screen with the curved side down as shown in figure 19.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 770-8473H CrrftsmrnPreparation Fety RulesProduct Specifications WarrantyMaintenance Agreement Full ONE Year Warrantyon Craftsmangas CHIPPER-SHREDDERAccessories TABI.E ContentsIndex Tools Requiredfor Assembly Assembly InstructionsFlat --/1 Washer 16 I.D Hex Lock Nut 5/16-18 Thread Hex Bolt 16-18 x 8-3/8 LongAttaching the Hopper Assembly Attachingthe Upper Guide AssemblyHOWTOSET-UPYOURCHIPPER-SHREDDER Attaching the Catcher BAGEngine SHUT-OFF SWITCHmUsed to stop Meets Ansi Safety StandardsOperation Know Your CHIPPER-SHREDDERTostopengine MUM Into the Hopper ASSEMBLY. Material UP to a Maximum of 3HOWTOUSEYOURCHIPPER-SHREDDER Could ResultOIL Notper INCHUTEUSE. Door is Closed WhenGAS To Stop Engine To StartengineChoke Engine Customer ResponsibilitiesGeneralrecommendations CHIPPER-SHREDDERClean Engine AIR CleanerFuel Filter Fler Area to Remove ALL Grass Dirt and Combustible DebrisStorage Service & AdjustmentRemoving the Flail Screen Chipper Blades Sharpeningor Replacingthe BladesShredding Blade Carburetoradjustment ThrottleadjustmentTires FlailsHOW to ORDI-R Replacement Parts Trouble ShootingPart Number Part Description Sears Craftsman 5 H.P. CHIPPER-SHREDDER Model no Sears Craftsman 5 H.P. Chipp ER-SHREDDER Model no Assemblies include all parts shown in frames. J Requires Special ToolsAssemblies include all parts shown in frames Repair Parts134 137 118 *493765111 535429 Carburetor Overhaul KIT Gasket SETCarburetor Gasket SET Mijlching and Bagging Irrftsmrn

247.795950 specifications

The Craftsman 247.795950 is a powerful and versatile snow blower designed to tackle the toughest winter conditions. With its robust construction and user-friendly features, it is an excellent choice for homeowners looking to keep their driveways and walkways clear of snow.

One of the standout features of the Craftsman 247.795950 is its strong engine. Powered by a dependable gas engine, this snow blower provides reliable performance, making it capable of clearing heavy snowfalls with ease. The engine is designed for efficient fuel consumption, ensuring that users can get the job done without constantly refueling.

The machine features a 24-inch clearing width, allowing it to clear a wide path in a single pass. This is particularly beneficial for those with larger driveways or property areas, as it reduces the time and effort needed to clear snow. The unit is equipped with an adjustable pitch auger that not only efficiently gathers and throws snow but also allows users to control the distance and direction of the snow discharge.

The Craftsman 247.795950 incorporates innovative technologies to enhance its usability. With its electric start feature, starting the snow blower in cold conditions becomes a hassle-free experience. This eliminates the need for tedious manual pulls while ensuring that the machine is ready to work when you are.

Another significant characteristic is its six-speed transmission, which includes two reverse speeds. This feature allows for greater control when navigating through challenging snow conditions, whether you're moving forward or backward. The ease of maneuverability is further enhanced by its large, heavy-duty tires, which provide excellent traction on slippery surfaces.

The snow blower is also designed with user comfort in mind. Its ergonomic handles are adjustable, allowing users to set them at a comfortable height. This feature reduces fatigue during prolonged use, making snow clearing less of a chore. Additionally, the hand warmers ensure that operators can work comfortably even in frigid temperatures.

Overall, the Craftsman 247.795950 stands out for its combination of power, efficiency, and user-centric features, making it a reliable tool for managing winter weather challenges. Whether facing light flurries or severe snowfall, this snow blower is engineered to perform efficiently, ensuring that winters are a little easier to navigate. Its durable construction and thoughtful features make it a solid investment for any homeowner.
Top Page Image Contents