Craftsman 316.79499 manual Spark Plug, Spark Arrestor Screen Collar Assembly, Storage

Page 15

MAINTENANCE AND REPAIR INSTRUCTIONS

SPARK PLUG

1.To remove spark plug (B) (Fig. 26) for cleaning or replacement: make sure engine is off, spark plug is cool, then grasp spark plug boot firmly and remove from spark plug. Remove spark plug with correct spark plug tool. Inspect, clean or replace as needed.

2.Spark plug gap = .025" (.635mm) (Figure 25).

3.Torque to 105 to 130 inch pounds (12 to 15 N•m). Connect spark plug boot.

4.If need replace spark plug with Champion RDJ8J or equivalent.

.025" (.635mm)

Spark

Plug

Fig. 25

SPARK ARRESTOR SCREEN/

COLLAR ASSEMBLY

1.To replace spark arrestor screen/collar assembly (A) (Figure 26), use a needle nose pliers and pinch an edge of the collar. Pull out the whole spark arrestor screen assembly.

2.Use the needle nose pliers to push in a new spark arrestor screen assembly by opening the pliers slight- ly to press the inner surface of the asembly securely into place

STORAGE

Failure to follow these steps may cause varnish to form in the carburetor which can cause difficult starting or per- manent damage following storage.

1.Perform all the general maintenance recommended in the Maintenance Section of your User Manual.

2.Clean exterior of engine and blower tubes.

3.Drain fuel from the fuel tank by running the unit dry or by removing the fuel cap and tipping the motor hous- ing/fuel tank over and draining oil/fuel mixture into a container with the same 2-cycle fuel mixture.

4.After fuel is drained, start engine.

5.Run engine at idle until unit stops. This will purge the carburetor of fuel.

6.Allow engine to cool (approx. 5 minutes).

7.Using a spark plug wrench, remove the spark plug.

8.Pour 1 teaspoon of clean 2-cycle oil into the combustion chamber. Pull starter rope slowly several times to coat internal components. Replace spark plug.

9.Store unit in a cool, dry place away from any source of ignition such as an oil burner, water heater, etc.

REMOVING A UNIT FROM STORAGE

1.Remove spark plug.

2.Pull starter rope briskly to clear excess oil from com- bustion chamber.

3.Clean and gap spark plug or install a new spark plug with proper gap. (Fig. 25)

4.Prepare unit for operation.

5.Fill fuel tank with proper fuel / oil mixture. See Fuel and Lubrication Section.

B

A

Fig. 26

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operator’s Manual Warranty Statement Table of ContentsFuel Safety Warnings Rules for Safe OperationRead ALL Instructions Before Operating While Operating Other Safety Warnings Safety and International Symbols Blower Components Know Your BlowerOIL and Fuel Mixing Instructions OIL and Fuel InformationAssembly Instructions Attach Flex TubeAttach Operating Tube Adjust Back Pack Harness and Control Handle STARTING/STOPPING InstructionsAttach Intermediate Tube and CON- Centrator Nozzle Stopping the Engine Important Idling InformationOperating Instructions Blower OperationsOperation Instructions Hours Maintenance and Repair InstructionsMaintenance Schedule Maintenance ChecklistIdle Adjustment AIR FilterFuel CAP / Fuel Filter Removing a Unit from Storage Spark Arrestor Screen Collar AssemblySpark Plug StorageUnit WON’T Start or Starts but will not RUN TroubleshootingEngine SpecificationsService Spare Parts List Specify Model NO. When Ordering Parts 30CC Back Pack Blower California / EPA Emission Control Warranty Statement

316.79499 specifications

The Craftsman 316.79499 is a versatile and powerful tool that stands out in the realm of a high-performance woodworking equipment. Recognized for its robust design and user-friendly features, this tool caters to both professional woodworkers and DIY enthusiasts alike.

One of the main features of the Craftsman 316.79499 is its strong motor that delivers exceptional performance across a range of applications. With a power output that allows for various speeds, users can adapt their work easily, ensuring precision and efficiency in every project. The tool is designed with adaptability in mind, making it suitable for cutting, shaping, and finishing tasks.

Another significant characteristic of the Craftsman 316.79499 is its ergonomic design. The tool is lightweight yet sturdy, allowing for comfortable handling over extended periods. This design consideration reduces user fatigue, making long work sessions more manageable. Additionally, the strategically placed grips enhance control, ensuring that even intricate cuts can be executed with precision.

In terms of technology, the Craftsman 316.79499 boasts several advanced features that enhance its functionality. One such feature is its built-in dust collection system. This technology helps maintain a clean workspace, reducing the need for frequent clean-ups and allowing users to focus on their craftsmanship. The dust collection system not only improves visibility but also promotes a healthier working environment.

Safety is also a top priority in the design of the Craftsman 316.79499. It comes equipped with multiple safety features, including a safety switch that prevents accidental starts, providing peace of mind during operation. Furthermore, the tool is designed to minimize vibration, which not only enhances control but also reduces the risk of hand fatigue.

In summary, the Craftsman 316.79499 is a well-rounded tool that combines power, versatility, and user-friendly features. Its strong motor, ergonomic design, and innovative technologies make it a reliable choice for woodworkers of all skill levels. Whether you are cutting, shaping, or finishing wood, the Craftsman 316.79499 stands ready to meet and exceed your expectations. With its commitment to safety and performance, it continues to be a popular choice in the woodworking community.
Top Page Image Contents