Craftsman 316.35084 manual STARTmNG a Cold ENGmNE, STARTmNG a Warm ENGmNE

Page 11

STOPPmNG mNSTRUCTmONS

1.Release the trigger and allow the engine to return to the idle speed.

2.Move the STOP switch up to the STOP position (Fig. 4).

NOTE: For emergency stopping, push the Neverof the chain brake lever/hand guard (C) forward and move the STOP switch up (Fig. 3, 4).

STARTmNG A COLD ENGmNE

To be sure to add the correctly mixed fuel to the fuel tank

(A) and to add bar and chain oil to the oil tank (B). Make

sure the chain brake is disengaged (C) before starting the unit.

1.Slide the STOP switch down (Fig. 4). The red choke meyer(H) has 3 positions: Positions 1, 2 and 3 (Fig. 6).

2.Fully press and release the primer bulb (G) 10 times, slowly. Some amount of fuel should be visible in the primer bulb (Fig. 5). If you can't see fuel in the bulb, press and release the bulb as many times as it takes before you can see fuel in it.

3.Move the red choke meyer(H) to Position 1 (Fig. 6). NOTE: This unit will not run with the lever in Position 1.

4.Place the saw on a firm flat surface. Hold saw firmly as shown (Fig. 7).

NOTE: The unit uses the INOREDI-PULL TM starting system with MAX FIRE IGNITION TM, which signifi- cantly reduces the effort required to start the engine. You must pull the starter rope out far enough to hear the engine attempt to start. There is no need to pull the rope briskly-- there is no harsh resistance when pulling. Be aware that this starting method is vastly different from (and much easier than) what you may be used to.

5.Hold down safety trigger (E) and squeeze the throttle trigger (D). With thumb, press down on the throttle latch (F). Release trigger (D) first. This will lock the throttle into wide open position (Fig. 3). Pull the rope with a controlled and steady motion 4 times.

6.Then move the red choke lever (H) to Position 2, being sure to keep the throttle trigger locked. Hold saw firmly and pull rope until saw starts. This could take 4 more pulls,

7.Let the saw warm up for 10 seconds, Depress and release throttle trigger (D) for idle.

8.Move red choke lever (H) to Position 3. If engine fails to start, repeat these instructions. If engine does start, begin chain brake test described on next page.

9.If unit idles roughly, there is an idle adjustment access hole (L)(Fig. 8). Using a Phillips or slotted screwdriver, turn screw 1/4 to 1/2 turn clockwise (to the right). Unit should then idle properly (Fig. 9).

NOTE: If chain turns while idling - turn screw back to the left until chain stops and unit continues to idle.

STARTmNG A WARM ENGmNE

F

E

F_g.3

Slider Stop Switch

F_g. 4

FWg.5

H

F_g.6

F_g.7

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Sears, Roebuck and Co., Hoffman Estates, L 60179, U.S.A Operators ManualEngine Exhaust from THiS Operate Your SAW Safely Safety mNSTRUCTmONSAvoidacddentaistarting,Beinthestartingposition Shutoff theenginebeforesettingthechainsawdownKickback Safety Precautions Fuel Safety Donotstartacutusingthetip of thesawOther Safety Precautions ON/OFF Control CHAroN SAW Components Safety FeaturesKICKBACKSPECiFiCS OraLAND Fuel MmXmNG mNSTRUCTmONS 95rnmBefore Starting Engine OperatethisunitonlySTARTmNG a Warm ENGmNE STARTmNG a Cold ENGmNEWARNmNG WARNmNG atreethathasbeenNever walk in front of m BUOKmNG USmNG a Sawhorse UMBmNGBUCKmNG IVAmNTENANCE Schedule Maintenance Checklist Hours of Opera Each USE TionReplacing Guide BAR and Chain Removing Guide BAR and ChainSAW CHAroN Tension Adjustment Fuel Filter AiR FilterSpark Plug OraLFILTERSpark Arrester Screen SAW Chain / BAR Lubrcaton STORmNGA CHAroNSAWREMOVmNG a UNmT from Storage Gude BAR MantenanceCHAroN Maintenance Guide BAR MaintenanceDealer Fouled Spark plug RPM RPM 9NAB NUT California / EPA Emission ControJ Warranty Statement U..,,,,,1

316.35084 specifications

The Craftsman 316.35084 is a versatile and reliable tool that has been designed to meet the needs of both professionals and DIY enthusiasts. Known for its durability and ease of use, this tool is a valuable addition to any workshop. Whether you are tackling home improvement projects or working on a professional job site, the 316.35084 is built to deliver performance that you can count on.

One of the main features of the Craftsman 316.35084 is its robust motor. With a powerful output, it allows for quick and efficient operation, making tasks like cutting, sanding, and drilling much easier. The motor has been engineered to provide high torque, which ensures that even tough materials can be handled with ease. This is particularly important for users who often work with dense woods or metals.

Another standout feature of this tool is its ergonomic design. The handle is crafted for comfort, allowing for a secure grip during extended use. This emphasis on user comfort not only enhances overall productivity but also reduces the risk of fatigue. In addition, the lightweight construction of the Craftsman 316.35084 makes it easy to maneuver, facilitating precision work in various environments.

Technologically, the Craftsman 316.35084 incorporates advanced features that enhance its functionality. For instance, it comes with multiple speed settings that can be adjusted according to the specific task at hand. This flexibility allows users to optimize the tool's performance, whether they need to achieve fine details or take on heavier-duty work. The tool also features a quick-change accessory system, enabling users to switch between different attachments with minimal downtime.

Safety is another critical characteristic of the Craftsman 316.35084. It comes equipped with built-in safety features, such as a protective casing and automatic shut-off mechanisms, which help prevent accidents during operation. This focus on safety ensures that users can work confidently without compromising their well-being.

Overall, the Craftsman 316.35084 stands out in the market for its combination of powerful performance, user-centric design, and safety features. With its ability to handle a variety of tasks effectively, it earns its place as a go-to tool for anyone serious about their crafting or construction endeavors. Whether you are a seasoned pro or just starting out, the 316.35084 is a tool that you can trust to get the job done right.
Top Page Image Contents